Bosch Appliances Air Conditioner NDA FMT200 DOME User Manual

IP200 MiniDome In-Ceiling Mount  
NDA-FMT200-DOME  
en Installation Manual  
 
IP200 MiniDome In-Ceiling Mount  
Table of Contents | en  
3
Table of Contents  
1
Safety  
4
1.1  
Safety precautions  
4
2
Unpacking  
5
2.1  
Parts List  
5
3
Installation Overview  
6
4
Installing a Recessed Mount  
Overview  
7
7
4.1  
4.2  
4.3  
Installing the Recessed Mount  
Installing the Camera to the Recess Mount  
7
11  
5
Connection  
14  
Bosch Security Systems  
Installation Manual  
AM18-Q0626 | v1.0 | 2012.09  
 
4
en | Safety  
IP200 MiniDome In-Ceiling Mount  
1
Safety  
Before installing and operating the camera, please read this  
manual carefully.  
1.1  
Safety precautions  
DANGER!  
High risk: This symbol indicates an imminently hazardous  
situation such as "Dangerous Voltage" inside the product.  
If not avoided, this will result in an electrical shock, serious  
bodily injury, or death.  
WARNING!  
Medium risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in minor or moderate bodily  
injury.  
CAUTION!  
Low risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in property damage or risk of  
damage to the unit.  
NOTICE!  
This symbol indicates information or a company policy that  
relates directly or indirectly to the safety of personnel or  
protection of property.  
This manual is the intellectual property of Bosch Security  
Systems and is protected by copyright. All rights reserved.  
AM18-Q0626 | v1.0 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
IP200 MiniDome In-Ceiling Mount  
Unpacking | en  
5
2
Unpacking  
This equipment should be unpacked and handled with care. If  
an item appears to have been damaged in shipment, notify the  
shipper immediately.  
Verify that all the parts listed in the applicable Parts List below  
are included. If any items are missing, notify your Bosch  
Security Systems Sales or Customer Service Representative.  
The original packing carton is the safest container in which to  
transport the unit and must be used if returning the unit for  
service. Save it for possible future use.  
2.1  
Parts List  
The following table lists the parts included in the In-ceiling  
(recessed) mount (NDA-FMT200-DOME):  
Quantity Part  
1
1
In-ceiling mount: NDA-FMT200-DOME  
White trim ring A (inner diameter: 102 mm)  
with two M3 captive screws  
1
White trim ring B (inner diameter: 98 mm) with  
two M3 captive screws  
4
4
1
1
Four M4 x 6 mm screws  
Four M4 x 15 mm screws  
Security Torx T-10 L wrench  
Installation manual (this booklet)  
Bosch Security Systems  
Installation Manual  
AM18-Q0626 | v1.0 | 2012.09  
 
6
en | Installation Overview  
IP200 MiniDome In-Ceiling Mount  
3
Installation Overview  
The IP200 MiniDome camera comes with the hardware and  
installation instructions necessary to mount the camera to a  
concrete ceiling.  
This following mounting accessory is available :  
In-ceiling mount, used in applications where the camera is  
mounted into a recessed ceiling.  
The mount is supplied with two different trim rings and  
different tooling hole positions on the sides of the recess  
mount. Use the table below to choose the ring and hole  
position for your camera.  
Trim ring  
Ring A  
Ring B  
Hole  
A
B
Camera  
NDN-265-PIO  
NDC-225-P  
NDC-225-PI  
NDC-255-P  
NDC-265-P  
The installation should be made by qualified installation  
personnel and conform to the National Electrical Code and  
applicable local codes.  
AM18-Q0626 | v1.0 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
IP200 MiniDome In-Ceiling Mount  
Installing a Recessed Mount | en  
7
4
Installing a Recessed Mount  
4.1  
Overview  
This chapter details how to install a recessed mount for the  
IP200 MiniDome.  
NOTICE!  
The image sensors in modern cameras are highly sensitive and  
require special care for proper performance and extended  
lifetime. Follow the guidelines for optimum results with your  
camera:  
Do not expose to direct sunlight or bright spotlights in  
operating and nonoperating conditions.  
Avoid bright lights in the field of view of the camera. Bright  
lights cause a “smearing” effect, which is visible as white  
lines above and below the highlight. Prolonged exposure to  
bright lights may cause bleaching of the sensor's color  
filters. This will be visible as colored spots in the picture  
and is irreversible.  
4.2  
Installing the Recessed Mount  
To mount to a recess mount, do the following:  
1. Determine a secure location for the recessed mount.  
194 (7.64)  
Figure 4.1 Recess Mount Dimensions  
Bosch Security Systems  
Installation Manual  
AM18-Q0626 | v1.0 | 2012.09  
 
8
en | Installing a Recessed Mount  
IP200 MiniDome In-Ceiling Mount  
2. Drill or cut a 7 in. hole with a tolerance of +/- 1/8 in.  
(177.8 mm +/- 2.2 mm).  
3. Optional: if installing the camera to a suspended ceiling  
tile or any other surface where additional support is  
required, the LTC 9349MK mounting kit (sold separately)  
is recommended. See the instruction book supplied with  
the mounting bracket for installation instructions.  
Figure 4.2 Mounting bracket  
4. Align holes of mounting plate (supplied with dome) with  
mounting bracket and attach with screws. Ensure that  
both the crescent shape of the mounting plate and the  
crescent shape of the mounting bracket are aligned.  
5. Ensure that the clamping plates are angled inward by  
pushing up and into the two slots.  
6. Insert mount through the hole and into the ceiling. Slide  
clamps out and down so that the drywall is clamped in  
between the clamps and the bracket flange, 41.7 mm  
(1.64 in.) maximum ceiling thickness and 9.7 mm (0.38 in.)  
minimum ceiling thickness).  
AM18-Q0626 | v1.0 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
IP200 MiniDome In-Ceiling Mount  
Installing a Recessed Mount | en  
9
Figure 4.3 Attach Recess Mount to Ceiling  
Figure 4.4 Attach Recess Mount to Ceiling  
7. Tighten both clamps to the ceiling using supplied screws  
and a #2 Phillips screwdriver.  
Bosch Security Systems  
Installation Manual  
AM18-Q0626 | v1.0 | 2012.09  
 
10 en | Installing a Recessed Mount  
IP200 MiniDome In-Ceiling Mount  
Figure 4.5 Tighten Mounting Clamps  
NOTICE!  
Over torquing the ceiling clamps can damage the clamp or  
ceiling. Only tighten the clamp until it contacts the ceiling and  
you start to feel some resistance. If using a power screwdriver,  
set the torque level to the lowest setting.  
AM18-Q0626 | v1.0 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
IP200 MiniDome In-Ceiling Mount  
Installing a Recessed Mount | en 11  
4.3  
Installing the Camera to the Recess Mount  
To install the camera to the recess mount, follow these steps:  
CAUTION!  
All wires for installation applications must be routed through a  
grounded conduit.  
1. Route wires on the side of mounting plate with the  
crescent shaped cut-out.  
2. Connect the cables according to the instructions in the  
IP200 MiniDomes Installation Manual.  
Figure 4.6 Match Connectors  
Cable out  
3. Attach the camera to the recess mount by removing the  
upper housing/bubble from the camera (use the wrench  
supplied with the camera), and attaching the camera base  
Bosch Security Systems  
Installation Manual  
AM18-Q0626 | v1.0 | 2012.09  
 
12 en | Installing a Recessed Mount  
IP200 MiniDome In-Ceiling Mount  
to the mount using the M4 x 15 mm mounting screws.  
Ensure that the cable is aligned with the cutout in the  
recess mount.  
4. Attach the camera base, and then install the upper  
housing/bubble. (See the camera User Manual for details.)  
Figure 4.7 Attach Camera to Recess Mount  
NOTICE!  
The recessed mounting bracket is provided with an additional  
safety tether point. To prevent injury, attach a safety wire from  
a secure anchor point above the ceiling to this tether point.  
5. Align the two mounting screws attached to the trim ring  
with the two mounting holes in the recess mount.  
AM18-Q0626 | v1.0 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
IP200 MiniDome In-Ceiling Mount  
Installing a Recessed Mount | en 13  
Figure 4.8 Align Trim Ring  
6. Fit the plastic trim ring. Use the supplied T-10 Torx wrench  
to secure the trim ring’s two safety locking screws to the  
mounting bracket.  
Bosch Security Systems  
Installation Manual  
AM18-Q0626 | v1.0 | 2012.09  
 
14 en | Connection  
IP200 MiniDome In-Ceiling Mount  
5
Connection  
After the camera is mounted, connect the network cable and  
the power cable.  
CAUTION!  
Do not connect power to the camera until all other connections  
are made.  
CAUTION!  
Installation should only be performed by qualified service  
personnel in accordance with the National Electrical Code or  
applicable local codes.  
CAUTION!  
All wires for installation applications must be routed through a  
grounded conduit.  
CAUTION!  
To prevent humidity problems, the camera must be installed in  
dry conditions, and the cable leads should be sealed once  
connected.  
Please refer to the IP200 Minidome series User Manual for  
further instructions on camera connections and configuration.  
AM18-Q0626 | v1.0 | 2012.09  
Installation Manual  
Bosch Security Systems  
 
 
Bosch Security Systems  
© Bosch Security Systems, 2012  
 

Black Box TV Converter Box A S 4 User Manual
Bogen Wireless Office Headset ADP1 User Manual
Briggs Stratton Automobile Parts 170799 User Manual
Bryant Air Conditioner 39006DP11 B User Manual
ButtKicker Stereo Amplifier BKA1000 N User Manual
Canon Scanner DR 5020 User Manual
Casio Clock TQ 377 User Manual
Christie Digital Systems Projector LX66A User Manual
Cisco Systems Computer Accessories CSACS3415K9 User Manual
Cisco Systems IP Phone 7900 Series User Manual