Bosch Appliances Car Video System TC9217MM W User Manual

TC9217MM-W, TC9220MM-W, TC9227MM-W  
Instruction Manual  
EN Monitor Mounts  
 
Installation and Assembly  
BOSCH Monitor Wall Mounts  
Models: TC9217MM-W, TC9220MM-W,  
TC9227MM-W  
BOSCH  
Before you start make sure all parts  
shown (see parts list, page 9) are  
included with your bracket.  
IMPORTANT! Read entire  
instruction sheet before you  
start installation and assembly.  
This product is intended for use with UL  
Listed products and must be installed by a  
qualified professional installer.  
R
IMPORTANT! If attaching a VCR Mount  
Product is UL rated up to ___ TV  
sizes, per attached chart  
carefully study both product instruction sheets  
before assembly. The interface bracket  
(included with the VCR Mount) must be  
attached during monitor mount assembly to  
avoid disassembly later.  
TV size  
17"  
Model #:  
TC9217MM-W  
TC9220MM-W  
TC9227MM-W  
21"  
27"  
Each monitor mount is for use with a single TV or monitor of a specified size only.  
SIDE VIEW  
TV  
TV  
A
CENTEROF  
GRAVITY  
B
C
FLOOR  
Place TV onto a piece of pipe as  
shown. (Pipe should be a few inches  
wider than the TV.) Roll TV back and  
forth to find the balance point. This is  
the center of gravity. Mark the center  
of gravity on the side of the TV.  
Adjust support tray (A, three  
pieces) to match width of TV.  
Lock support tray using four  
carriage bolts (B), washer/  
nut combo (C). Tighten  
securely.  
Attachadhesive  
pads (X) to top  
clamps (Q).  
CC  
R
Q
Insert plastic  
covers(CC)onto  
endsofanti-rollout  
hooks(R).  
X
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
3 of 12  
 
Attach support tray (A)  
to vertical support arms  
(P) as shown.  
Note: Choose the square  
hole which aligns closest  
with the center of gravity  
mark on the TV (as  
Y
R
determined in step 1).  
Attach anti-rollout hooks  
(R) as shown using M6  
screws(Z)andretainer  
bars (Y). Note: Extruded  
side of retainer bar (Y)  
goestowardsanti-rollout  
hook(R).  
R
Y
Z
P
P
E
Y
Hand tighten only.  
R
A
J
O P T I O N A L  
Although top clamps (Q) and anti-rollout  
hooks (R) [see step 7] will provide more than  
adequate support for the TV, some installers  
may wish to also attach the support tray to  
the TV bottom.  
F
A
Using uni-clips (G) and M5 screws (F) (see  
instruction card in fastener pack), or #10 x  
3/4" particle board screws (H) and washers  
(I) (for attachment to mounting bosses if  
present), or a combination of both, attach  
support tray (A) to TV bottom. [To do this  
place TV upside down on a flat stable  
surface and position support tray upside  
down on TV bottom.] Attach at four places  
as close to the four corners of the TV bottom  
as possible.  
G
H
I
TV  
(UPSIDE DOWN)  
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
4 of 12  
 
For Wood Stud Walls drill three 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm) into stud center.  
Attach wall arm (W) using three #14 x 2.5" (6 mm x 65 mm) wood screws (V).  
WARNING  
• Tighten wood screws so wall arm is firmly attached, but do not tighten with excessive force! Overtightening can  
cause stress damage to wood screws, greatly reducing their holding power. Tighten to 80 in • lb (9 N.M.) maxi-  
mum torque.  
W
V
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
5 of 12  
 
WARNING  
• When installing BOSCH wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete  
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid  
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-  
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill  
to avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard-  
ware and components.  
For Concrete Walls use wall arm (W), making sure  
that it is level, as a template to mark holes. Drill 1/  
1
concrete  
wall  
4" (6 mm) dia. holes to a minimum depth of 2.5" (64  
mm). Insert concrete anchors in holes flush with  
wall as shown (right). Place wall arm (W) over  
anchors and secure with #14 x 2.5" (6 mm x 65  
mm) wood screws (V). Tighten all fasteners.  
ACC 204  
Drill hole(s) and insert anchor(s)  
WARNING  
2
wall arm  
• Tighten wood screws so that wall plate is firmly  
attached, but do not overtighten. Overtightening can  
damage the screws, greatly reducing their holding  
power.  
ACC 204  
• Never tighten in excess of 80 in • lb (9 N.M.).  
Place arm over anchor(s) and secure with screw(s)  
• Make sure that mounting screws are anchored into the  
center of the studs. The use of an "edge to edge" stud  
finder is highly recommended.  
3
WARNING  
• Concrete anchors are not intended for attachment to  
concrete wall covered with a layer of plaster, drywall,  
or other finishing material. If mounting to concrete wall  
covered with plaster/drywall is unavoidable, plaster/  
drywall (up to 5/8" thick) must be counterbored as  
shown below. If plaster/drywall is thicker than 5/8",  
custom fasteners must be supplied by installer.  
Tighten all fasteners  
CUTAWAYVIEW  
ACC 204  
INCORRECT  
CORRECT  
CONCRETE  
WALL  
wall  
arm  
concrete  
concrete  
wall  
arm  
W
plaster/  
dry wall  
plaster/  
dry wall  
V
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
6 of 12  
 
Note: Slots in corners of top clamps (Q) and corners of vertical support arms (P) allow for the installation of safety belt  
(model ACC 666, sold separately). If using this belt, install it now.  
DETAIL 1  
Q
Q
Q
DETAIL 2  
R
Z
Q
R
P
R
A
P
R
K
P
Position TV onto support tray (A). Position anti-rollout hooks (R) against front edge of TV.  
WARNING  
• Each anti-rollout hook (R) should have at least 1/4” of surface contact with the front of the TV. If this is not the  
case the support tray (A) must be adjusted smaller [see step 2], or the vertical support arms (P) adjusted inward  
[see step 4].  
Insert top clamps (Q). Note: Top clamps (Q) fit between rollout protectors (R) and vertical support arms (P)  
[DETAIL 1]. Press down on each top clamp (Q) while securely tightening each M6 screw (Z).  
By hand, thread one serrated flange head screw (K) into each vertical support arm (P) into one of three threaded  
holes [1, 2, or 3; DETAIL 2]. Choose the threaded hole that will allow just enough tilt clearance [see step 9].  
Leaveabout1/4"ofexposedthread.  
FIRST: From the top fully thread flush mount tube  
(T) into threaded fitting in wall arm or ceiling plate.  
Install the wall arm or ceiling plate according to  
instructions included with it.  
WMJ 025H  
NEXT: Attach right and left tilt brackets (AA & BB)  
to horizontal support (S) using four screws &  
WMJ 018,  
WMJ 022  
T
CMJ 470,  
CMJ 480,  
CMJ 490  
*
washer combo (J). Before tightening screws make  
sure tilt brackets are adjusted horizontally to align  
precisely with screws in the side of vertical support  
arms (P). Attach horizontal support (S) to wallarm  
or ceiling plate using fiber washers (M & N), spacer  
(U, only included with smaller models) and retaining  
collar (O). IMPORTANT:Retainingcollar(O)  
** U  
T
N
S
BB  
requires a safety screw [refer to DETAIL 3, page 8].  
M
O
FINALLY: Be sure that hooks in right and left tilt  
brackets (AA & BB) are open end forward. Hang the  
TV / bracket assembly.  
AA  
J
WARNING  
• Do not lift more weight than you can handle!  
Use additional manpower or mechanical lifting  
equipment to safely lift and hang the TV /  
Bracket assembly!  
Wall arms & ceiling plates  
include their own  
instructions. Fixed length  
and adjustable extension  
columns are also available.  
*
Included with models  
TC9217MM and  
TC9220MM only.  
**  
Insert one screw & washer combo (J) through slot  
in each tilt bracket (AA & BB). Hand tighten.  
P
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
7 of 12  
 
S
T
F
S
O
When attaching the horizontal support (S) to wall arm or  
ceiling plate, carefully thread retaining collar (O) onto end of  
flush mount (T) tube (or extension column). Tighten at least  
four complete turns ending with one of the small threaded  
holes aligned with slot in the end of flush mount tube (T) (or  
extension column). Insert and tighten one M5 screw (F).  
DETAIL 3  
(BOTTOM VIEW)  
WARNING  
• Set screw (F) is self tapping and may be hard to get  
started but is essential to this installation. Failure to  
install this screw can cause the mount to fall.  
TIL  
T
CLEARANCE  
Adjust TV to desired tilt then tighten screws. Maximum tilt  
is 30°. If tilt clearance is a problem revisit step 7, DETAIL 2.  
WARNING  
• Tighten all screws securely.  
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
8 of 12  
 
Parts List  
TC9217MM-W TC9220MM-W TC9227MM-W  
Description  
Qty.  
1
1
1
4
4
2
6
4
4
4
8
2
1
1
1
2
2
2
1
1
1
4
1
2
2
2
1
1
2
Part #  
Part #  
Part #  
left end support tray  
right end support tray  
center support tray  
5/16 - 18 x 1/2" carriage bolt  
5/16-18 washer/nut combo  
M10-1.5 x .7 flange nut  
M5 x .8 x 10 mm screw  
uni-clip  
128-1023  
128-1024  
128-1128  
520-9207  
530-1016  
520-9261  
520-9250  
2245-081  
500-9006  
540-9400  
520-1041  
520-1105  
540-9432  
540-9431  
1800-375  
128-1107  
128-1138  
128-1116  
128-1016  
1446-014  
128-0067  
128-1026  
128-1027  
128-1134  
520-9207  
530-1016  
520-9261  
520-9250  
2245-081  
500-9006  
540-9400  
520-1041  
520-1105  
540-9432  
540-9431  
1800-375  
128-1109  
128-1138  
128-1116  
128-1017  
1446-014  
128-0067  
128-1026  
128-1027  
128-1135  
520-9207  
530-1016  
520-9261  
520-9250  
2245-081  
500-9006  
540-9400  
520-1041  
520-1105  
540-9432  
540-9431  
1800-375  
128-1111  
128-1138  
128-1116  
128-1018  
1446-014  
-
A1  
A2  
A3  
B
C
E
F
G
H
#10 x 3/4" particle board screw  
#10 flat washer  
I
M10 socket head lock/flat washer combo screw  
M10 serrated flange head screw  
fiber washer - large inside dia.  
fiber washer - small inside dia.  
retaining collar  
J
K
M
N
O
P
vertical support arm  
top clamp  
anti-rollout hook  
Q
R
horizontal support  
S
flush mount tube  
T
spacer  
U
#14 x 2.5" (6 mm x 65 mm) screw  
single wall arm  
adhesive pads (not shown)  
retainer bar  
5S1-015-C03 5S1-015-C03 5S1-015-C03  
V
W
X
128-1059  
570-0024  
128-1117  
520-1166  
128-1342  
128-1341  
590-1055  
128-1059  
570-0024  
128-1117  
520-1166  
128-1337  
128-1336  
590-1055  
128-1069  
570-0024  
128-1117  
520-1166  
128-1337  
128-1336  
590-1055  
Y
M6 x 18mm flat phillips screw  
tilt bracket right  
tilt bracket left  
Z
AA  
BB  
CC  
plastic cover for anti-rollout hook  
Note: Parts may appear slightly different than illustrated.  
R
T
Y
U
N
Y
P
B
BB  
S
M
O
A1  
W
R
P
X
A3  
Q
C
X
AA  
A2  
Q
V
E
F
K
H
J
I
G
Z
CC  
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
9 of 12  
 
GENERAL WALLMOUNTKITSPECIFICATIONS  
Mount  
TV/Monitor  
ProductBOSCHrated  
when attached to...  
Support  
Tray  
Depth(D)  
concrete,  
wood  
Model  
Number  
cinder block  
or brick  
stud  
Screen Size  
125 lb  
(57 kg)  
150 lb  
(65 kg)  
10"  
(254 mm)  
13" - 17"  
TC9217MM-W  
TC9220MM-W  
(330 mm) (432 mm)  
125 lb  
(57 kg)  
150 lb  
(65 kg)  
14"  
(356 mm)  
19" - 21"  
(482 mm) (533 mm)  
125 lb  
(57 kg)  
150 lb  
(65 kg)  
14"  
(356 mm)  
25" - 28"  
TC9227MM-W  
(635 mm) (686 mm)  
Reach (R)  
18" (457 mm) for models TC9217MM-W, TC9220MM-W.  
22.5" (572 mm) for models TC9227MM-W.  
WARNING  
• Weight of TV or monitor not to exceed Max. Load  
Capacity (BOSCH rating)!  
R
300 tilt  
range  
TV  
support tray  
D
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
10 of 12  
 
11 of 12  
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05  
 
Americas  
Europe, Middle East, Africa  
Bosch Security Systems B.V.  
P.O. Box 80002  
5600 JB Eindhoven, The Netherlands  
E-mail:  
Asia-Pacific  
Bosch Security Systems Pte Ltd  
38C Jalan Pemimpin  
Singapore 577180, Singapore  
Phone: +65 319 3488  
Bosch Security Systems  
130 Perinton Parkway  
Fairport, New York, 14450, USA  
Phone: +1 (585) 223 4060  
Fax:  
+1 (585) 223 9180  
Fax:  
E-mail:  
+65 319 3499  
© 2005 Bosch Security Systems GmbH  
3935 890 28113 05-05 | February 3, 2005 | Data subject to change without notice.  
 

Belkin Surge Protector BZ106200IR2M User Manual
Blue Rhino Charcoal Grill CBT711W User Manual
Blue Rhino Outdoor Fireplace 252207 User Manual
Boss Audio Systems Car Stereo System RV 70 User Manual
Bowers Wilkins Portable Speaker Signature 805 User Manual
Bushnell Binoculars 13 Nov User Manual
Califone Microphone Q319 User Manual
Carson Car Amplifier SA 365 10 User Manual
Casablanca Fan Company Fan 54000 User Manual
Casio Electronic Keyboard XW P1 User Manual