Bosch Appliances Home Security System 00P User Manual

LTC9316/00P  
Security Systems  
Installation Manual  
Standard Pole  
EN  
 
LTC9316/00P  
Instruction Manual  
Installation  
3
EN  
7.778  
24"  
6"  
4X  
O
1.000  
BASED ON A 11.00" B.C.  
6"  
36"  
32"  
24"  
13.0007.778  
4.000  
24"  
O
11.000  
4.000  
O
3.000  
13.000  
24"  
32"  
36"  
Figure 3 Anchor Bolt Dimensions  
PV4 Anchor jig (if applicable)  
NOTE: Prepare the concrete per manufacturer's  
directions. The concrete must have a compressive  
!
8"  
8"  
strength of 3000 psi, and must be fabricated following  
ACI318-89 requirements. Allow the concrete  
foundation to cure thoroughly before proceeding with  
the installation.  
12"  
12"  
32"  
36"  
Reinforcement bars (12)  
Figure 4 View of Concrete Foundation  
Figure 2 Reinforcement Bars  
3. FOR ANCHOR BOLT INSTALLATIONS:  
4.2 Installation  
Pour concrete per manufacturer's directions, making sure that  
the wiring conduit is in the center of the pad. See Figure 3  
(next page) for dimensions of the bolt pattern and suspend  
appropriate bolts in the concrete around the wiring conduit.  
Leave 2" to 3" of the Bolts protruding above the pad. If you are  
using leveling nuts, leave 4" to 6" protruding.  
NOTE: Be sure that the pole is oriented properly, with the  
carriage.  
!
1. Place the pole on the pad with the holes on the Base Plate  
aligned with the bolts of the anchor bolts or anchor jig  
(Figure 5).  
2.  
Remove the access opening plates at the bottom and top.  
Bosch Security Systems 10 October 2003  
 
LTC9316/00P  
Instruction Manual  
Installation  
4
EN  
Access opening plates  
Bolts or  
anchor jig  
Figure 7 Lifting the Pole into Position  
CAUTION: Pull all slack in the wiring as you lift the pole into  
position to keep from pinching and possible damage.  
Pad  
Figure 5 Placement of Pole on Pad  
6. Ensure that the pole is vertical on all sides. Use a  
bubble level or plumb bob to check.  
3. Insert the wiring into the 3" diameter hole in the base of the  
pole. Be sure all slack is pulled completely through.  
7. Secure the pole to the pad with fasteners (Figure 8).  
4. Insert connecting wiring into the bottom access opening, run  
through the pole up to the top access opening. Insert the end  
rough the housing connecting hole. Close the top access  
opening and make necessary wiring connections at the bottom  
access opening (Figure 6).  
Nut  
Lock Washer  
Top access opening  
Flat Washer  
Figure 8 Securing the Pole to the Pad  
®
4.3 Mounting the AutoDome  
1. Align the holes of the AutoDome adapter plate with the  
holes on the mounting plate at the top of the pole  
(Figure 9).  
Figure 6 Connecting Wiring Through Pole  
5. Slowly lift the pole into the upright position, aligning  
the holes of the Base Plate with the Bolts in the concrete  
pad (FigurBosch Security Systems10 October 2003e 7).  
Bosch Security Systems 10 October 2003  
 
Mount the LTC 9540/xx  
Wall Bracket Using  
These Holes  
Adapter Plate  
Figure 9 Aligning Adapter Plate with Mounting Plate  
Figure 11 Mounting the LTC 9540/xx Wall Bracket  
2. Attach the LTC 9540/xx Wall Bracket adapter plate, using  
the provided hex head nuts and bolts, flat washers, and  
lockwashers (see Figure 10).  
5
SPARE PARTS  
Part No.  
LTC9316AP  
Description  
LTC 9540/xx Wall Arm  
Adapter Plate  
Lockwashers  
Flat Washers  
5/16-18 Nuts  
Figure 10 Attaching the Adapter Plate  
3. Attach the LTC 9540/xx Wall Bracket to the adapter plate  
using recommended 8 mm (5/16-inch) bolts/studs (refer to  
the LTC 9540/xx Installation Instructions). Bolts should be  
secured with nuts, washers, and lockwashers.  
 
Bosch Security Systems, Inc.  
850 Greenfield Road  
Robert Bosch GmbH  
Geschäftsbereich  
Bosch Security Systems B.V.  
P.O. Box 80002  
Lancaster, PA 17601 EE.UU.  
Tel: 800-326-3270  
Postfach 10 60 50  
70049 Stuttgart  
5600 JB Eindhoven  
The Netherlands  
Fax: 1-717-735-6560  
Telefax (0711) 811-12 34  
Tele +31 40 27 80000  
© 2005 Bosch Security Systems GmbH  
3935 890 38012 28  
June  
Data subject to change without notice.  
 

Black Decker Power Screwdriver 5145342 00 User Manual
Bolens Snow Blower 1026 User Manual
Bose Speaker System 151 User Manual
Boston Acoustics Speaker ASW 250 User Manual
Braun Coffeemaker Tassimo User Manual
Bushnell Telescope 78 2010 User Manual
Campbell Hausfeld Staple Gun CHN10610 User Manual
Canon Camera Lens EF24 105MM User Manual
Canon Fax Machine FAX TT250 User Manual
Char Broil Charcoal Grill 463621611 User Manual