Bosch Appliances Home Security System CC408 User Manual

CC408  
Operators Guide  
EN Solution 880  
 
CC408 | Operators Guide | Contents  
EN | 3  
Reset Latching Outputs.................................14  
15.  
16.  
Contents  
Codepad ID/Buzzer Tone Change..............14  
1.  
2.  
3.  
Introduction......................................................5 17.  
Testing.............................................................14  
Horn Speaker Test.........................................14  
Bell Test ..........................................................14  
Strobe Test......................................................14  
Walk Test Mode.............................................14  
Test Report.....................................................14  
17.1  
17.2  
17.3  
17.4  
17.5  
Specifications ....................................................5  
Features .............................................................5  
4.  
Codepad Indicators..........................................6  
Zone Indicators.................................................6  
AWAY Indicator..............................................6  
STAY Indicator................................................6  
System Disarmed..............................................6  
4.1  
4.2  
4.3  
4.4  
4.5  
4.6  
4.7  
4.8  
4.9  
18.  
19.  
Event Memory Recall....................................15  
Day Alarm ......................................................15  
Remote Arming By Telephone ....................15  
MAINS Indicator .............................................7 20.  
Off Indicator/Zone Sealed ..............................7  
On Indicator/Zone In Alarm..........................7  
FAULT Indicator .............................................7  
Audible Indications..........................................7  
21.  
21.1  
21.2  
Domestic Dialling ..........................................16  
Acknowledging Domestic Calls....................16  
Programming Domestic Telephone  
Numbers..........................................................16  
21.3  
Disable Domestic Dialling ............................16  
5.  
Arming the System...........................................7  
Arming in AWAY Mode.................................8  
Arming in STAY Mode 1................................8  
Arming in STAY Mode 2................................8  
Programming STAY Mode 2 Zones ..............9  
5.1  
5.2  
5.3  
5.4  
22.  
22.1  
Partitioning .....................................................17  
Master Partitioned Codepad Indicators.......17  
22.1.1 Zone Indicators ..............................................17  
22.1.2 Area On/Off Indicators.................................17  
22.2.1 Area Display Indicators.................................17  
22.2.2 Status Indicators.............................................17  
6.  
Disarming the System......................................9  
7.  
User Codes........................................................9  
Adding User Codes..........................................9  
Adding Radio Remote User Codes................9  
Deleting User Codes/Radio User Codes.......9  
22.3  
Operating From A Master Partitioned  
Codepad..........................................................17  
Operating From Area Addressable  
Codepads ........................................................17  
7.1  
7.2  
7.3  
22.4  
8.  
Radio Transmitter Operations......................10  
23.  
24.  
25.  
Basic Pager Reporting ...................................18  
Glossary of Terms..........................................20  
Installation Notes ...........................................22  
9.  
Alarms .............................................................10  
Duress Alarm..................................................10  
Panic Alarm ....................................................10  
Fire Alarm.......................................................11  
Medical Alarm................................................11  
Tamper Alarm (Access Denied) ...................11  
9.1  
9.2  
9.3  
9.4  
9.5  
Figures  
Figure 1:  
Figure 2:  
Figure 3:  
CP5 Eight Zone LED Codepad...............6  
CP5 Eight Zone LCD Codepad..............6  
RE012 – 2 Channel Keyfob  
Transmitter ..............................................10  
RE013 – 4 Channel Keyfob  
Transmitter ..............................................10  
CP5 LED Codepad Showing Audible  
Alarm Buttons .........................................10  
Master Partitioned Codepad..................17  
Basic Pager Display ................................19  
10.  
10.1  
10.2  
Isolating Zones................................................11  
Standard Isolating ..........................................11  
Code to Isolate ...............................................11  
Figure 4:  
Figure 5:  
11.  
Setting the Date and Time ............................11  
12.  
Fault Analysis Mode ......................................12  
AC Fail............................................................12  
System Faults..................................................12  
Fault Descriptions...........................................12  
Figure 6:  
Figure 7:  
12.1  
12.2  
12.3  
13.  
Telco Arm/Disarm Sequence (Call Forward  
On/Off) ...........................................................13  
13.1  
13.2  
Telco Arm Sequence......................................13  
Telco Disarm Sequence.................................13  
14.  
Turning Outputs On/Off...............................14  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | Contents  
EN | 4  
Tables  
Table 1:  
Table 2:  
Table 3:  
Table 4:  
Table 5:  
Table 6:  
Table 7:  
Table 8:  
Table 9:  
Specifications.............................................5  
Zone Indicator...........................................6  
AWAY Indicator.......................................6  
STAY Indicator.........................................6  
MAINS Indicator......................................7  
FAULT Indicator ......................................7  
Audible Indicators.....................................7  
Arming Methods.......................................7  
Keyfob Audible/Visual Indications ......10  
Table 10: Fault Condition Indicators.....................12  
Table 11: Telco Arm/Disarm Dialling Digits........13  
Table 12: Domestic Dialling Telephone Digits.....16  
Table 13: Zone Status Display Descriptions..........18  
Table 14: System Status...........................................18  
Table 15: Glossary of Terms...................................20  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 1. Introduction  
EN | 5  
1.  
Introduction  
3. Features  
Congratulations on selecting the Solution 880 Model  
CC408 Control Panel to protect you and your  
The Solution 880 Control Panel uses the latest in  
microprocessor technology to provide you with more  
property. To obtain the most from your unit, take the useful features and superior reliability and  
time to read through this manual and familiarise  
yourself with the operating features of this system. In  
all aspects of planning, engineering, styling,  
operation, convenience, and adaptability, we have  
sought to anticipate your every possible requirement.  
performance. The main features of the control panel  
are listed below:  
xꢀ Eight programmable User Codes  
xꢀ STAY Mode and AWAY Mode operation  
xꢀ Six programmable burglary zones  
xꢀ Two programmable 24-hour zones  
xꢀ Siren and/or dialler lockout per zone  
xꢀ Delayed reporting  
Programming simplicity and speed were some of the  
major considerations and we believe that our  
objectives in this area were more than satisfied.  
This guide explains all aspects of operating the  
control panel. All system parameters and options are  
detailed. Suitability is left up to the individual. Every  
system can be tailored to meet all requirements  
quickly and easily.  
xꢀ Built-in telephone fail monitor  
xꢀ Day alarm  
xꢀ Remote arming  
xꢀ Answering machine bypass  
xꢀ Event memory recall  
2. Specifications  
Table 1:  
Specifications  
xꢀ Upload/download programmable  
xꢀ Auxiliary output (Output 2)  
xꢀ Relay output  
0oC to +45oC  
Temperature Range  
(+32oF to +113oF)  
10% to 95%  
TF008 Plug Pack –  
240 VAC/18 VAC @ 1.3 A  
65 mA  
Humidity  
Power Source  
xꢀ Eight radio remote user codes  
xꢀ Entry and exit warning beeper  
xꢀ EDMSAT – satellite siren compatible  
xꢀ Separate fire alarm sound  
xꢀ Dual reporting  
Stand-By Current  
Current Draw In  
Alarm Condition  
Current Draw In  
Alarm Condition  
with Codepad  
115 mA  
105 mA  
xꢀ Sensor watch  
xꢀ Dynamic battery testing  
6 Ah/12 VDC Rechargeable  
sealed lead acid battery  
30.6 cm x 26.2 cm x 8.4 cm  
Back-Up Battery  
xꢀ Automatic arming/automatic disarming  
xꢀ AC fail and system fault indicators  
xꢀ Walk Test Mode  
Dimensions (case,  
packed in carton)  
Weight  
Supplier Code  
New Zealand  
Telepermit  
(12.05 in. x 10.31 in. x 3.31 in.)  
2.5 Kg (5.51 lb.)  
N771  
PTC 211/98/083  
xꢀ Monitored siren output (Output 1)  
xꢀ Strobe output  
Pending  
Malaysia Approval  
Number  
xꢀ Telco arm/disarm sequence (call forwarding)  
The Austel permit issued for this product  
is subject to the following conditions:  
The Solution 880 Model CC408 Control  
Panel can only be powered by a Bosch  
Security Systems TF008 Plug Pack  
(Approval Number Q92128).  
Test the sirens, strobe, and zones at  
weekly intervals. See Section 17 Testing  
for further information.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 4. Codepad Indicators  
EN | 6  
4.2  
AWAY Indicator  
4. Codepad Indicators  
Figure 1: CP5 Eight Zone LED Codepad  
The AWAY indicator displays the  
system is armed in AWAY Mode. The  
AWAY indicator also flashes in unison  
with the STAY indicator when  
programming various options  
throughout the Operators Guide.  
See Section 5.1 Arming in AWAY Mode  
for information on the different  
methods of arming the system in  
AWAY Mode.  
Table 3:  
AWAY Indicator  
Definition  
Figure 2: CP5 Eight Zone LCD Codepad  
AWAY  
Indicator  
On  
Off  
System is armed in AWAY Mode.  
System is not armed in AWAY Mode.  
4.3  
STAY Indicator  
The STAY indicator displays the system  
is armed in STAY Mode 1 or STAY  
Mode 2. The STAY indicator also flashes  
in unison with the AWAY indicator  
when programming various options  
throughout the Operators Guide.  
The codepad is the communications interface  
between you and your alarm system. Use the  
codepad to issue commands. The codepad offers  
both visual and audible indications that guide you  
through the general operation.  
See Section 5.2 Arming in STAY Mode 1 for  
different methods of arming in STAY  
Mode 1. See Section 5.3 Arming in STAY  
Mode 2 to arm in STAY Mode 2.  
The codepad incorporates numerous indicators.  
There are zone indicators that show the condition of  
each zone and four other indicators for general  
status. The following pages outline a list of situations  
and the relevant indicators that are seen.  
Table 4:  
STAY Indicator  
Definition  
STAY  
Indicator  
On  
System is armed in STAY Mode 1 or  
STAY Mode 2.  
System is not armed in STAY Mode 1  
or STAY Mode 2.  
Zone Isolating Mode or setting STAY  
Mode 2 zones.  
4.1  
Zone Indicators  
The zone indicators (1 to 8) display  
1 2 3 ….  
Off  
the status of the zones. Table 2 lists the  
various situations that the indicators  
display (such as, Zone Sealed/Zone  
Unsealed).  
Flashing twice  
a second  
Flashing once  
every 3  
Day alarm status – day alarm turned  
on.  
Table 2:  
Zone Indicator  
seconds  
4.4  
System Disarmed  
This indicator displays with the  
indicator when the system is disarmed.  
Zone Indicator  
On  
Off  
Definition  
Zone is unsealed.  
Zone is sealed.  
Flashing Fast  
Zone is in alarm condition.  
(0.25 seconds on/  
0.25 seconds off)  
Flashing Slow  
(1 second on/  
1 second off)  
Zone is manually isolated or  
selected to be isolated.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 5. Arming the System  
EN | 7  
4.5  
MAINS Indicator  
The MAINS indicator displays the  
systems AC mains supply is normal or  
failed.  
Table 7:  
Audible Indicators  
Audible Indicator  
One short beep  
Definition  
A button was pressed on the  
Table 5:  
MAINS Indicator  
codepad, or end of exit time when  
armed in STAY Mode 1 or STAY  
Mode 2.  
The system accepted your code.  
The requested function was  
executed.  
Indicates the end of exit time when  
armed in AWAY Mode, or the  
requested operation was denied or  
aborted.  
Walk Test Mode is currently active  
or warning before automatic arming  
takes place.  
MAINS Indicator  
On  
Flashing  
Definition  
AC mains power normal.  
AC mains supply failed.  
Two short beeps  
Three short beeps  
4.6  
Off Indicator/Zone Sealed  
One long beep  
The  
indicator displays when the  
system is in the disarmed state and  
flashes when a zone becomes unsealed  
during the disarmed state. The  
indicator stops flashing when all zones  
are sealed.  
One beep every  
second  
One short beep  
every minute  
There is a system fault waiting to  
be acknowledged.  
4.7  
4.8  
On Indicator/Zone In Alarm  
The  
indicator displays when the  
system is armed in AWAY Mode and  
flashes when an alarm occurs. The  
indicator resets once a valid user code  
is entered.  
5. Arming the System  
There are several ways to arm the system depending  
on whether you are:  
xꢀ Leaving the premises and require all active zones  
FAULT Indicator  
to be in a ready state for an intruder.  
The FAULT indicator displays the  
system detected a system fault. See  
Section 12. Fault Analysis Mode for  
additional information on system faults.  
xꢀ Remaining in the premises and only require part  
of the system to be in a ready state for an  
intruder.  
If a zone is not sealed at the end of exit time, the  
zone is automatically isolated and constantly displays  
on the remote codepad. The zone becomes an active  
part of the system when the zone reseals. For  
example, if a window is left open after exit time  
expires, the window is not an active part of the  
system until the window is closed. Opening the  
window after exit time expired causes an alarm  
condition.  
Every time a new system fault is  
detected (such as, FAULT indicator  
flashing), the codepad beeps once  
every minute. Pressing the [#] button  
once cancels the once a minute beep  
and acknowledges the fault (such as,  
FAULT indicator on steady).  
Table 6:  
FAULT Indicator  
Table 8 defines the different methods for arming the  
system.  
FAULT  
Definition  
Indicator  
On  
Table 8:  
Arming Methods  
There is a system fault that must be  
rectified.  
Off  
Flashing  
The system is normal, there are no faults.  
There is a system fault that must be  
acknowledged.  
AWAY Mode  
Arms the entire system. See Section 5.1  
Arming in AWAY Mode.  
Arms all zones except those programmed  
to be automatically isolated by the  
installer. See Section 5.2 Arming in  
STAY Mode 1.  
Arms all zones except those programmed  
to be automatically isolated by the Master  
Code holder. See Section 5.3 Arming in  
STAY Mode 2.  
STAY Mode 1  
4.9  
Audible Indications  
Table 7 defines the audible indicators  
generated by the codepad buzzer.  
STAY Mode 2  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 5. Arming the System  
EN | 8  
If the Entry Guard Timer For STAY Mode 1 is  
Forced Arming  
programmed and a zone not automatically isolated is  
triggered, the codepad beeps twice per second until  
the entry timer expires or the system disarms. If the  
alarm condition is not reset by entering your user  
code followed by the [#] key (for example,  
[2 5 8 0 #]) before the entry timer expires, the sirens  
activate into alarm. Only your installer can program  
this feature.  
The feature of arming the system when a zone is not  
sealed is known as forced arming. If the system does  
not arm and a long beep is heard, forced arming is  
not permitted. If this is the case, ensure that all zones  
are sealed or manually isolated before arming the  
system.  
5.1  
Arming in AWAY Mode  
When you leave your premises and require all zones  
to be in a ready state to detect intrusion, you arm the  
system in AWAY Mode. When returning to your  
premises, disarm your system (see Section 6. Disarming  
the System) so you do not sound a false alarm.  
Arming in STAY Mode 1, Method 1  
Enter your user code followed by the [*] key (for  
example, [2 5 8 0 *]). Two beeps sound and the  
STAY indicator displays. Exit time starts counting.  
Any zones programmed to be automatically isolated  
in STAY Mode 1 flash until exit time expires. At the  
end of exit time, all zones selected to be  
automatically isolated turn off and the codepad gives  
one short beep.  
There are two different methods for arming the  
system in AWAY Mode. Method one is standard and  
always operates. Method two is optional and may be  
disabled by your installer if you do not want to use  
single button arming.  
Arming in STAY Mode 1, Method 2  
Arming in AWAY Mode, Method 1  
Hold down the [*] button until two beeps are heard.  
The STAY indicator displays and exit time starts  
counting.  
Enter your user code followed by the [#] key (for  
example, [2 5 8 0 #]). Two beeps sound and the  
AWAY indicator displays. Exit time starts counting.  
Any zones programmed to be automatically isolated  
in STAY Mode 1 flash until exit time expires. At the  
end of exit time, the zone indicators turn off and the  
codepad emits one short beep.  
Arming in AWAY Mode, Method 2  
Hold down the [#] key until two beeps sound.  
The AWAY indicator displays and exit time starts  
counting.  
5.3  
Arming in STAY Mode 2  
5.2  
Arming in STAY Mode 1  
STAY Mode 2 is only used when the perimeter and  
unused areas of the premises must be armed to  
detect an intruder from entering the premises while  
you move freely within an area that is automatically  
isolated. Any Master Code user can program zones  
to be automatically isolated in STAY Mode 2.  
STAY Mode 1 is only used when the perimeter and  
unused areas of the premises must be armed to  
detect if an intruder is entering the premises. At the  
same time it allows you to move freely within an area  
that is automatically isolated.  
Entry Guard Timer For STAY Mode 2  
Only your security company can program  
zones automatically isolated in STAY  
Mode 1.  
When arming the system in STAY Mode 2, an  
optional entry timer called Entry Guard Timer For  
STAY Mode 2 is available. Use this entry timer to  
delay the sirens if a zone is not automatically isolated  
and triggered into alarm condition. Entry Guard  
Timer for STAY Mode 2 is the delay time used for  
all zones except 24-hour zones when the system is  
armed in STAY Mode 1 or STAY Mode 2.  
There are two different methods for arming the  
system in STAY Mode 1. Method one is standard  
and always operates. Method two is optional and  
may be disabled by your installer if you do not want  
to use single button arming.  
Entry Guard Timer for STAY Mode 1  
If the Entry Guard Timer For STAY Mode 2 is  
programmed and a zone not automatically isolated  
triggers, the codepad beeps twice a second until the  
entry timer expires or the system disarms. If the  
alarm condition is not reset by entering your user  
code followed by the [#] button (for example,  
[2 5 8 0 #]) before the entry timer expires, the sirens  
activate into alarm. Only your installer can program  
this option.  
When arming the system in STAY Mode 1, an  
optional entry timer called Entry Guard Timer For  
STAY Mode 1 is available. Use this entry timer to  
delay the sirens if a zone is not automatically isolated  
and triggers an alarm condition. Entry Guard Timer  
For STAY Mode 1 is the delay time used for all  
zones except 24-hour zones when the system is  
armed in STAY Mode 1 or STAY Mode 2.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 6. Disarming the System  
EN | 9  
How to Add a User Code  
Arming in STAY Mode 2  
1. Enter your four-character Master Code, followed  
by [1] and [#] (for example, [2 5 8 0 1 #]).  
Three beeps sound and the STAY and AWAY  
indicators flash.  
Hold down the [0] button until two beeps sound.  
The STAY indicator lights and exit time starts  
counting.  
Any zones programmed to be automatically isolated  
in STAY Mode 2 flash until exit time expires. At the  
end of exit time, all zones selected to be  
automatically isolated extinguish and the codepad  
provides one short beep.  
2. Enter the user code number (1 to 8) followed by  
the [#] key (for example, [2 #] = User 2, [8 #] =  
User 8). Two beeps sound and the selected user  
number displays on the codepad indicators.  
3. Enter the digits required for the new code  
followed by the [#] key (for example, for user  
code 5768, enter [5 7 6 8 #]). Two beeps sound  
and the STAY and AWAY indicators turn dark.  
To add or change other user codes, repeat this  
procedure as many times as required.  
5.4  
Programming STAY Mode 2 Zones  
You can only program zones to be automatically  
isolated in STAY Mode 2 if you have a Master Code.  
How to Program STAY Mode 2 Zones  
1. Enter your four-character Master Code, followed  
by the [4] and [#] keys (for example,  
7.2  
Adding Radio Remote User Codes  
Only the Master Code holder can add or change  
other system user codes, including the Master Code.  
Up to eight radio user codes (User Codes 9 to 16)  
can be programmed to operate the system.  
[2 5 8 0 4 #]). Three beeps sound and the STAY  
indicator flashes.  
2. Enter the zone number to be automatically  
isolated, followed by the [*] key (for example,  
[1 *] = Zone 1, [2 *] = Zone 2).  
How to Add a Radio Remote User Code  
1. Enter your four-character Master Code, followed  
by the [1] and [#] keys (for example,  
The selected zone flashes. If you make a mistake,  
enter the same zone number followed by the [#]  
key to clear the incorrect zone.  
To select additional zones to be automatically  
isolated in STAY Mode 2, repeat Step 2 as many  
times as required.  
[2 5 8 0 1 #]).  
Three beeps sound and the STAY and AWAY  
indicators flash.  
2. Enter the radio remote user code number (9 to  
16), followed by the [#] key (for example, [9 #] =  
User 9, [1 6 #] = User 16). Two beeps sound and  
the selected user number displays on the  
codepad indicators.  
3. To exit this mode, press the [#] key when you  
have selected all zones to be automatically  
isolated in STAY Mode 2. Two beeps sound and  
the STAY and AWAY indicators turn dark.  
3. Press any button on the keyfob so the system  
learns the ID number. Two beeps sound and the  
STAY and AWAY indicators extinguish.  
To add or change other radio remote user codes,  
repeat this procedure as many times as required.  
6. Disarming the System  
When you enter the premises after the system is  
armed in AWAY Mode, or if you have armed the  
system in STAY Mode 1 or STAY Mode 2, you must  
disarm the system before entry time expires to  
disable detection devices that activate an alarm. Only  
your installer can program the entry time.  
7.3  
Deleting User Codes/Radio User  
Codes  
Only the Master Code holder can delete other  
system user codes.  
If there was an alarm condition prior to disarming  
the system, a flashing zone indicator displays  
indicating a previous alarm on that zone.  
How to Delete a User Code  
1. Enter your four-character Master Code, followed  
by the [1] and [#] keys (for example,  
How to Disarm the System  
Enter your user code followed by the [#] key (for  
example, [2 5 8 0 #]). Two beeps sound.  
[2 5 8 0 1 #]).  
Three beeps sound and the STAY and AWAY  
indicators flash.  
2. Enter the user code number (User Code 1 to 8,  
Radio User Code 9 to 16), followed by the [#]  
key (for example, [2 #] = User 2, [1 6 #] = User  
16). Two beeps sound and the selected user  
number displays on the codepad indicators.  
3. Press the [*] key to delete the selected user code.  
Two beeps sound and the STAY and AWAY  
indicators turn dark. To delete other user codes,  
repeat this procedure as many times as required.  
7.  
7.1  
User Codes  
Adding User Codes  
Only the Master Code holder can add or change  
other system user codes, including the Master Code.  
Up to eight user codes can be programmed to  
operate the system.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 8. Radio Transmitter Operations  
EN | 10  
Table 9:  
Keyfob Audible/Visual Indications  
8. Radio Transmitter  
Operations  
Figure 3: RE012/E – 2 Channel Keyfob  
Transmitter  
Indication  
One beep  
Two beeps  
Two-tone beep  
3-second strobe  
6-second strobe  
Definition  
System disarmed.  
System armed in AWAY Mode.  
System armed in STAY Mode.  
System disarmed.  
System armed in AWAY or STAY  
Mode.  
1
3
2
9. Alarms  
9.1  
Duress Alarm  
A codepad duress alarm is used as a silent hold-up  
alarm. This only occurs when the number 9 is added  
to the end of any valid user code used to disarm the  
system (for example, [2 5 8 0 9 #]). A duress alarm is  
only useful if your system reports back to a  
monitoring station or pocket pager, because domestic  
reporting (such as a mobile phone) cannot decipher  
which type of alarm occurred.  
1 – Button 1: Arm or disarm in AWAY Mode  
2 – Button 2: Arm or disarm STAY Mode  
3 – Buttons 1 and 2: Press both buttons at same  
time to activate Panic alarm.  
Figure 5: CP5 LED Codepad Showing Audible  
Alarm Buttons  
Figure 4: RE013/E – 4 Channel Keyfob  
Transmitter  
1
3
2
4
1 – Button 1: Arm or disarm in AWAY Mode  
2 – Button 2: Arm or disarm in STAY Mode  
3 – Buttons 1 and 2: Press both buttons at same  
time to activate Panic alarm.  
9.2  
Panic Alarm  
4 – Buttons 3 and 4: Your security company can  
program these buttons for optional operation,  
such as operating a garage door.  
An audible alarm activates when the [1] and [3] keys  
or the [*] and [#] keys are pressed simultaneously.  
Contact your installer to disable the ability to activate  
the codepad panic alarm or to silence the codepad  
panic alarm.  
Audible/Visual Indications  
When using hand held keyfob transmitters to operate  
the system, your security company can program the  
keyfobs to sound the horn speaker or operate the  
blue strobe light. These indications allow you to  
operate the system from outside the premises with  
confidence.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 10. Isolating Zones  
EN | 11  
3. Press the [#] key after all selected zones are  
isolated.  
9.3  
Fire Alarm  
The horn speaker emits a distinct fire sound when  
both the [4] and [6] keys are pressed simultaneously.  
Contact your installer to disable the ability to activate  
the codepad fire alarm or to silence the codepad fire  
alarm.  
Two beeps sound and the system returns to the  
disarmed state.  
10.2 Code to Isolate  
Only those user codes with the Code to Isolate  
priority level can isolate zones. If any user code has  
this priority level, the standard isolating method (see  
Section 10.1 Standard Isolating) does not function.  
9.4  
Medical Alarm  
An audible alarm activates when both the [7] and [9]  
keys are pressed simultaneously. Contact your  
installer to disable the ability to activate the codepad  
medical alarm or to silence codepad medical alarm.  
How to Isolate a Zone  
1. Press the [*] key followed by your user code and  
the [*] key again to enter Isolating Mode (for  
example, [* 2 5 8 0 *]). Three beeps sound and  
the STAY indicator flashes.  
2. Enter the zone number (1 to 8), followed by the  
[*] key (for example, [1 *] = Zone 1, [2 *] =  
Zone 2).  
9.5  
Tamper Alarm (Access Denied)  
The tamper alarm restricts the number of times an  
invalid user code can be used in an attempt to  
operate the system. When the number of incorrect  
code attempts equals the number programmed by  
your installer, the system activates an alarm  
condition. If reporting back to a security monitoring  
station, the system sends an Access Denied Report.  
Each zone to isolate has a corresponding zone  
indicator that flashes. If you selected an incorrect  
zone to isolate, enter the incorrect zone number  
again followed by the [*] key.  
To shutdown and lockout a codepad for a period of  
time (0 to 150 seconds), ask your installer to program  
this feature.  
Repeat Step 2, if isolating more than one zone,  
until all zones to isolate are selected.  
3. Press the [#] key after all selected zones are  
isolated.  
10. Isolating Zones  
Isolating zones allow you to manually disable one or  
more zones before arming the system. Once a zone is  
isolated, you can access that zone during the armed  
state without activating an alarm.  
Two beeps sound and the system returns to the  
disarmed state.  
11. Setting the Date and Time  
Programming the date and time is only required  
when you need functions such as automatic test  
reports, automatic arming, and history events to  
operate correctly.  
For example, you may need to isolate a zone because  
before arming the system a PIR detector might  
generate a false alarm, or you need to leave a pet  
inside a particular zone while away.  
How to Program Date and Time  
1. Enter your Master Code followed by the [6] and  
[#] keys (for example, [2 5 8 0 6 #]).  
Three beeps sound and the STAY and AWAY  
indicators flash.  
2. Enter the day, month, year, hour, and minute  
using the (DD, MM, YY, HH, MM) format (that  
is, DD = day of the month, MM = month of the  
year, YY = current year, HH = hour of the day,  
MM = minute of the day).  
Isolating zones is performed by one of two methods.  
Method two is optional and only allows those user  
codes programmed by your installer access to isolate  
zones.  
10.1 Standard Isolating  
Standard Isolating allows all operators to isolate  
zones without knowing a valid user code.  
How to Isolate a Zone  
1. Press the [*] key twice to enter Isolating Mode.  
Three beeps sound and the STAY indicator  
flashes.  
2. Enter the zone number (1 to 8), followed by the  
[*] key (for example, [1 *] = Zone 1, [2 *] =  
Zone 2).  
When programming the hour of the day,  
you must use a 24-hour format.  
3. Press the [#] key to exit and return to the  
disarmed state.  
Each zone to isolate has a corresponding zone  
indicator that flashes. If you selected an incorrect  
zone to isolate, enter the incorrect zone number  
again followed by the [*] key.  
Two beeps sound and the STAY and AWAY  
indicators go dark. If a long beep sounds, an  
error was made when entering the date and time.  
Repeat Step 2 if you are isolating more than one  
zone, until all zones to isolate are selected.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 12. Fault Analysis Mode  
EN | 12  
Sensor Watch Fail  
A sensor watch fault registers because one or more  
detection devices failed to notice any movement  
during the disarmed state for the time period  
programmed by your installer. The fault clears when  
the zone in question detects movement and resets.  
12. Fault Analysis Mode  
If a fault occurs, the FAULT or MAINS indicators  
flash and the codepad beeps once every minute.  
12.1 AC Fail  
While in Fault Analysis Mode, hold down the [5] key  
until two beeps sound. The indicator lights that  
corresponds to the faulted zone.  
If the AC mains supply fails, the MAINS indicator  
flashes until the AC mains supply is restored.  
Pressing the [#] key once acknowledges the fault and  
stops the codepad from beeping once every minute.  
Horn Speaker Fail  
12.2 System Faults  
How to Determine the Type of System Fault  
A horn speaker failure fault registers when the  
system detects the horn speaker is disconnected. This  
fault clears once the horn speaker is reconnected.  
Your installer needs to program the system for this  
feature to operate.  
To determine all system faults other than the AC  
mains supply, enter Fault Analysis Mode:  
1. Hold down the [5] key until two beeps sound.  
The FAULT indicator lights steadily and the  
STAY and AWAY indicators flash in unison.  
Any zone indicators displayed indicate the type  
of fault that occurred. See Table 10 for the list of  
system faults that can occur.  
Telephone Line Fail  
A telephone line failure fault registers when the  
system detects the telephone line is disconnected  
from the control panel. Your installer needs to  
program the system for this feature to operate.  
2. To further determine the type of fault condition,  
hold down the key that corresponds to the zone  
indicator displayed.  
3. To exit Fault Analysis Mode and return to the  
disarmed state, press the [#] key. The FAULT  
indicator remains displayed and the codepad  
stops beeping once per minute.  
E2 Fault  
An E2 failure fault registers when the system detects  
an internal checksum error. Contact your installer as  
soon as this fault displays.  
Fuse Fail  
A fuse failure fault occurs when either of the two 1 A  
fuses are blown. Contact your installer as soon as this  
fault displays.  
12.3 Fault Descriptions  
Table 10: Fault Condition Indicators  
Communication Fail  
A communication fail fault registers when the control  
panel fails to communicate with the receiving party  
(for example, a monitoring company, mobile phone,  
pocket pager, and so on). The communication fault  
clears once the control panel successfully reports to  
the receiving party.  
Zone LED  
FAULT Condition  
Battery Fail  
Date/Time  
Sensor Watch  
Horn Speaker Fail  
Telephone Line Fail  
E2 Fault  
1
2
3
4
5
6
7
8
Fuse Fail  
Communication Fail  
Battery Fail  
A battery fail fault registers when the system detects  
a low capacity back-up battery. The system  
automatically performs a Battery Test every 4 hours  
and every time the system is armed.  
Date and Time  
The date and time fault registers every time the  
system powers down. This type of fault does not  
cause the FAULT indicator to display on the  
codepad unless your installer has programmed the  
automatic arming time. See Section 11. Setting the Date  
and Time to program the date and time.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 13. Telco Arm/Disarm Sequence (Call Forward On/Off)  
EN | 13  
3. Enter the call forward sequence (for example,  
[* 6 1][Phone Number][#] to program the Call  
Forward - No Answer sequence, or [* 2 1][Phone  
Number][#] to program the Call Forward  
Immediate sequence).  
To program a “*” in the Telco Arm Sequence,  
enter [* 1]. To program a “#” in the Telco Arm  
Sequence, enter [* 2].  
13. Telco Arm/Disarm  
Sequence (Call Forward  
On/Off)  
Use this feature to program the Telco Arm Sequence  
and Telco Disarm Sequence (Call Forward On/Off).  
4. Press the [#] key when finished.  
Two beeps sound, and the STAY and AWAY  
indicators go dark.  
13.1 Telco Arm Sequence  
Use this to program the Call Forward – Immediate  
On sequence or Call Forward – No Answer sequence  
to automatically operate when you arm the system in  
AWAY Mode. This feature is only available if your  
telecommunications provider has the call-forward  
option.  
To disable the Telco Arm Sequence,  
enter the call forward sequence as [* 4]  
(break) for Step 3.  
13.2 Telco Disarm Sequence  
This feature automatically disables the call forward  
sequence when disarming the system.  
The examples given in this feature are  
only applicable to Australia.  
How to Program the Telco Disarm Sequence  
Call Forward – Immediate On  
1. Enter your four-character Master Code followed  
by the [3] and [#] keys (for example,  
[2 5 8 0 3 #]).  
You can redirect calls to anywhere in Australia,  
including mobile phones, pagers, and answering  
services. When Call Forward is turned on, your  
telephone does not ring.  
Three beeps sound and the STAY and AWAY  
indicators flash.  
2. Press the [2] and [#] key to select the Telco  
Disarm Sequence. Three beeps sound.  
3. Enter the call forward disable sequence (for  
example, [# 6 1 #] to disable the No Answer  
Call Forward sequence, or [# 2 1 #] to disable  
the Call Forward Immediate sequence).  
To program a “#” in the Telco Disarm  
Sequence, enter [* 2].  
Call Forward – No Answer  
When your telephone is not answered within 20  
seconds, this feature redirects all incoming calls to  
another number anywhere in Australia, but you can  
still make outgoing calls.  
Table 11: Telco Arm/Disarm Dialling Digits  
4. Press the [#] key when finished.  
Two beeps sound, and the STAY and AWAY  
indicators go dark.  
Digit  
Number to  
Digit  
Required  
8
9
Number to  
Program  
8
9
Required Program  
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
To disable the Telco Disarm Sequence,  
enter the call forward sequence as [* 4]  
(break) for Step 3.  
*
#
*1  
*2  
*3  
*4  
4-sec pause  
break  
How to Program the Telco Arm Sequence  
1. Enter your four-character Master Code, followed  
by the [3] and [#] keys (for example,  
[2 5 8 0 3 #]).  
Three beeps sound and the STAY and AWAY  
indicators flash.  
2. Press button [1] and [#] keys to select the Telco  
Arm Sequence.  
Three beeps sound.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 14. Turning Outputs On/Off  
EN | 14  
14. Turning Outputs On/Off  
17. Testing  
This feature only applies if your installer set up an  
output that can be turned on or off by the codepad.  
The output programmed by your installer can  
control a pool pump, outside lighting, and so on. Up  
to three separate outputs may be programmed.  
There are various functions for testing that your  
system is operating correctly.  
17.1 Horn Speaker Test  
Press and hold the [1] key until two beeps sound.  
The horn speaker sounds for 2 seconds.  
How to Turn an Output On or Off  
17.2 Bell Test  
Press and hold the [2] key until two beeps sound.  
The bell output operates for 2 seconds.  
1. Enter your Master Code followed by the [5] and  
[#] keys (for example, [2 5 8 0 5 #]).  
Three beeps sound and the STAY and AWAY  
indicators flash.  
2. Enter the output number (1 to 3) that you wish to  
turn on or off.  
17.3 Strobe Test  
1. Press and hold the [3] key until three beeps  
sound.  
The strobe flashes.  
2. Press and hold the [3] key until two beeps sound.  
The strobe stops flashing.  
3. Press the [#] key to turn the output on, or press  
the [*] key to turn the output off.  
Three beeps sound if the output is turned on,  
and two beeps sound if the output is turned off.  
Repeat Step 2 and Step 3 if you require more  
than one output to be turned on or off.  
4. Press the [#] key to exit this function.  
Two beeps sound and the STAY and AWAY  
indicators go dark.  
17.4 Walk Test Mode  
Use Walk Test Mode to test detection devices for  
proper operation. Every time you test a zone, the  
codepad sounds one long beep and the horn speaker  
sounds one short beep to indicate the zone was  
activated when testing.  
15. Reset Latching Outputs  
1. Enter your four-character Master Code, followed  
by the [7] and [#] keys (for example,  
This feature only applies if your installer  
programmed an output to latch (remain on) until you  
acknowledge the event that occurred.  
[2 5 8 0 7 #]).  
Three beeps sound, and the STAY and AWAY  
indicators flash. The codepad beeps once every  
second while the system is in Walk Test Mode.  
2. Activate all zones that require testing.  
The codepad sounds one long beep and the horn  
speaker sounds one short beep every time a zone  
is faulted (unsealed) and restored.  
How To Reset Latching Outputs  
Hold down the [7] key until two beeps sound. The  
output resets.  
16. Codepad ID/Buzzer Tone  
Change  
Hold down the [8] key continuously to change the  
tone of the codepad buzzer. There are 50 different  
tones, from 1500 Hz to 5000 Hz. If multiple  
codepads are installed, each codepad can sound a  
different tone.  
3. When you finish testing all required zones, press  
the [#] key to exit this mode.  
Two beeps sound, and the STAY and AWAY  
indicators turn off. The system returns to the  
disarmed state.  
17.5 Test Report  
This feature only applies if your system reports by  
telephone. Press and hold the [9] key until two beeps  
sound. The system sends a Test Report without  
sounding the sirens.  
If the system is partitioned, the keypad first displays  
the area to which the keypad is assigned:  
xꢀ Zone 1: Area 1 codepad  
xꢀ Zone 2: Area 2 codepad  
xꢀ Zone 7: master partitioned codepad  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 18. Event Memory Recall  
EN | 15  
18. Event Memory Recall  
20. Remote Arming By  
Telephone  
Use this feature to arm your system from any remote  
location using a telephone. For security reasons, the  
system cannot be disarmed using this method. This  
feature requires a touch-tone telephone. Your  
installer must program this feature to operate.  
Use this function to replay the last 40 events that  
occurred to the system. The event memory history  
replays all alarms and arming/disarming of the  
system in AWAY Mode, STAY Mode 1, and STAY  
Mode 2.  
The system cannot differentiate between  
arming the system in STAY Mode 1 or  
STAY Mode 2.  
How to Remotely Arm your System Using the  
Telephone  
1. Call the telephone number connected to your  
control panel.  
2. When the control panel answers the incoming  
call, a short jingle is heard. To arm the system,  
press the [*] key on the touch-tone telephone for  
1 to 3 seconds.  
How to Enter Event Memory  
Enter your four-character Master Code followed by  
the [8] and [#] keys (for example, [2 5 8 0 8 #]).  
Three beeps sound. The last 40 events display one at  
a time by the codepad indicators, starting from the  
most recent event. A beep sounds as each event  
displays.  
If you hear modem tones when the control panel  
answers the incoming call, the system was  
programmed for remote programming functions  
by your installer. Wait for a pause between the  
tones before pressing the [*] key.  
19. Day Alarm  
Day alarm allows a combination of zones to be  
monitored during the disarmed state by beeping the  
codepad buzzer. Only your installer can program  
zones 1 to 4 to operate for day alarm.  
After releasing the [*] key on the touch-tone  
telephone, two beeps sound indicating that the  
system was armed in AWAY Mode.  
3. Hang up the telephone and the system remains  
armed.  
Example  
A day alarm can be set up at the front door of a shop  
with a pressure mat or electronic beam that  
customers activate as they enter and exit the shop. As  
the customers walk onto the pressure mat or break  
the electronic beam, the codepad buzzer beeps.  
If your installer programs answering  
machine bypass, you must call the control  
panel twice to make a connection with the  
system. For example, call the telephone  
number that your control panel is  
How to Turn Day Alarm On  
connected to, let the call ring no more  
than four rings, then hang up the  
telephone. Wait a minimum of 8 seconds  
before you call the control panel again.  
Hold down the [4] key until three beeps sound.  
Day alarm turns on. All zones programmed for day  
alarm operation cause the codepad buzzer to beep  
during the disarmed state when activated.  
How to Turn Day Alarm Off  
Hold down the [4] key until two beeps sound.  
Day alarm turns off.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 21. Domestic Dialling  
EN | 16  
How to Program Telephone Numbers  
1. Enter your four-character Master Code, followed  
by the [2] and [#] keys (for example,  
[2 5 8 0 2 #]).  
21. Domestic Dialling  
Domestic dialling is used to call your mobile phone  
or a relative/friend in the event your control panel  
activates an alarm. Up to three different telephone  
numbers can be programmed for the control panel to  
call when an alarm occurs. Only your installer can  
set the system to report in the domestic format,  
however, the Master Code holder can change the  
domestic telephone numbers at any time.  
Three beeps sound and the STAY and AWAY  
indicators flash.  
If there are telephone numbers already  
programmed, they are displayed one digit at a  
time by the codepad indicators.  
If there are no telephone numbers programmed,  
a further two beeps sound after entering this  
mode. These two beeps are normally heard after  
the last digit of the last telephone number  
displays.  
21.1 Acknowledging Domestic Calls  
When an alarm condition occurs, the system calls the  
first telephone number that was programmed. When  
you answer an incoming call, you hear the system  
sound a repeating siren tone followed by a pause,  
continually for 2 minutes (for example, siren tone,  
pause, siren tone, and pause).  
2. Enter all digits for the first telephone number (for  
example, [9 6 7 2 1 7 1 7]).  
As each digit is entered, the corresponding  
codepad indicators display.  
3. If there is more than one telephone number to  
be programmed, press [* 4]. This inserts a break  
between the first telephone number and the  
second telephone number. If there is only one  
telephone number to program, press the [#] key  
to exit this function.  
4. Enter all the digits of the second telephone  
number (for example, [9 6 7 2 1 0 5 5]).  
As each digit is entered, the corresponding  
codepad indicators display.  
5. After the last digit of the second telephone  
number is programmed, press the [#] key to exit  
this function unless a third telephone number is  
required. If there is a third telephone number to  
program, press the [* 4] button to insert a break  
between the second telephone number and the  
third telephone number.  
If you do not acknowledge the call from the control  
panel during a pause between siren tones, the control  
panel hangs up after 2 minutes expire, and calls the  
next telephone number.  
Pressing the [*] key for 1 to 3 seconds during the  
pause acknowledges the call and no further calls are  
made for that event. If the call is successfully  
acknowledged, a tone of decreasing pitch is heard.  
Table 12: Domestic Dialling Telephone Digits  
Digit  
Number  
Digit  
Number  
to Program  
8
9
Required to Program Required  
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
8
9
*
#
*1  
*2  
*3  
*4  
21.3 Disable Domestic Dialling  
To cancel domestic dialling (for example, you are  
moving and do not want the system to continue  
calling your mobile phone), enter the following  
sequence.  
4-sec. pause  
break  
1. Enter your four-character Master Code, followed  
by the [2] and [#] keys (for example,  
[2 5 8 0 2 #]).  
Two beeps sound and the STAY and AWAY  
indicators flash.  
2. Press the [*] button followed by the [4] and [#]  
keys (for example, [* 4 #]).  
21.2 Programming Domestic Telephone  
Numbers  
If your system is configured for domestic dialling,  
this function allows any Master Code holder to  
program telephone numbers the control panel calls  
in the event of an alarm.  
The STAY and AWAY indicators go dark.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 22. Partitioning  
EN | 17  
Mains Indicator  
This indicator displays the status of the AC mains  
supply. The indicator lights steadily when the AC is  
normal and flashes when there is an AC supply  
failure.  
22. Partitioning  
You can partition or split the Solution 880 Control  
Panel into two individual areas. You can operate  
both areas from one Master Partitioned codepad or  
from separate area addressable codepads.  
Fault Indicator  
This indicator displays the status of the system’s fault  
register. If the FAULT indicator flashes when the  
system detects a fault that has not yet been  
acknowledged. If the indicator lights steadily, the fault  
has been acknowledged.  
22.1 Master Partitioned Codepad  
Indicators  
Figure 6: Master Partitioned Codepad  
Partial Indicator  
This indicator shows whether an area is armed in  
STAY Mode 1. If the PARTIAL indicator is lit, the  
area is armed in STAY Mode 1. If the indicator is  
not lit, no areas are armed in STAY Mode 1. When  
isolating zones, the PARTIAL indicator flashes to  
indicate that you are in the isolate mode. The  
PARTIAL indicator also flashes in conjunction with  
the AUX indicator to indicate successful entry into  
any programming mode (for example, when using  
Master Code functions).  
22.2 Operating From A Master  
Partitioned Codepad  
If you have a partitioned system with a Master  
Partitioned codepad installed, operating procedures  
described throughout this guide are the same with  
one exception. All operations are relative to the area  
whose AREA DISPLAY indicator is illuminated at  
the time.  
The indicators on a Master Partitioned codepad are  
configured into four groups. The following  
paragraphs describe the indicators.  
22.1.1  
Zone Indicators  
The zone indicators (1 to 8) display the status of each  
zone. These zones belong to the area whose AREA  
DISPLAY indicator is lit. If a ZONE indicator is lit,  
that zone is unsealed. If a ZONE indicator is not lit,  
that zone is sealed.  
Example  
When the AREA DISPLAY indicator number 2 is lit,  
all operations performed affect only Area 2. To  
perform operations in another area, you must move  
the AREA DISPLAY illuminator to the desired area.  
22.1.2  
Area On/Off Indicators  
The group of four AREA ON/OFF DISPLAY  
indicators show the status of each area. If an  
indicator is lit, that area is armed. If the indicator is  
not lit, that area is disarmed.  
To Move From One Area To The Next  
Press the AWAY button.  
The area display indicator moves to the next area.  
Repeat until the desired indicator is lit.  
22.1.3  
Area Display Indicators  
A group of four AREA DISPLAY indicators  
determine the area to which the displayed zones  
belong.  
22.3 Operating From Area Addressable  
Codepads  
22.1.4  
Status Indicators  
If you have a partitioned system with Area Addressable  
codepads, the operating procedures described throughout  
this guide are the same. Refer to 16. Codepad ID/Buzzer  
Tone Change on page 14 to determine the area to which a  
particular codepad belongs.  
This group of four indicators shows the following:  
AUX Indicator  
The AUX indicator displays when the system is using  
the telephone line to communicate to the receiving  
party.  
The AUX indicator flashes in conjunction with the  
PARTIAL indicator to show successful entry into any  
programming mode. For example, this occurs when  
you are using Master Code functions.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 23. Basic Pager Reporting  
EN | 18  
System Status  
23. Basic Pager Reporting  
The system status information is divided into the four  
digits identified in Table 14.  
This feature only applies if your system reports to a  
pocket pager. Basic pager reporting requires some  
interpretation of the numbers that appear on the  
display. It is possible to differentiate between 1000  
different systems when a number of control panels  
report to the one pocket pager.  
Table 14: System Status  
System Status Description  
Display  
First digit  
Subscriber ID Number  
Indicates whether the system is armed  
or disarmed:  
8 = Disarmed  
9 = Armed  
Indicates which codepad alarm was  
triggered by the operator:  
0 = No Codepad Alarm  
1 = Codepad Panic or Duress Alarm  
2 = Codepad Fire Alarm  
This is the identification number of the control panel  
and can only be programmed by your installer.  
Zone Status  
Second digit  
The zone status display shows you the status of each  
zone (1 to 8). Table 13 describes what each number  
means when displayed on the zone status display.  
Table 13: Zone Status Display Descriptions  
3 = Codepad Medical Alarm  
Third digit  
Indicates when the AC mains supply  
fails:  
Number  
Displayed  
Zone  
Description  
0 = AC Supply is normal  
1 = AC Supply failed  
0
1
2
Zone Normal  
Indicates the corresponding zone is in the  
sealed state.  
Fourth digit  
Indicates when a system fault occurs  
at the control panel:  
0 = System Normal – There are no  
faults.  
1 = System Fault – There is a fault  
registered by the control panel.  
Alarm  
Indicates the corresponding zone is  
unsealed and in alarm condition.  
Zone Bypassed  
Indicates a system operator manually  
isolated the corresponding zone. See  
Section 10. Isolating Zones for  
information on how to manually isolate a  
zone(s) prior to arming the system.  
Figure 7 shows the transmission came from the  
control panel with an ID number of 678, and zone 2  
is in alarm. Figure 7 also displays zone 3 is manually  
isolated and the system is armed.  
3
Zone Trouble  
Indicates a zone was left unsealed after  
the end of exit time.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 23. Basic Pager Reporting  
EN | 19  
Figure 7: Basic Pager Display  
2
1
3
1
2
3 4 5 6 7 8  
678 01200000 9000  
4
5
6
7
8
1 – Subscriber ID number  
2 – Zone status  
3 – System status  
4 – 0: Zone Normal  
1: Alarm  
2: Zone Bypassed  
3: Zone Trouble  
5 – 8: Disarmed  
9: Armed  
6 – 0: Normal  
1: Panic/Duress  
2: Fire Alarm  
3: Medical Alar  
7 – 0: AC Normal  
1: AC Failure  
8 – 0: System Normal  
1: System Fault  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 24. Glossary of Terms  
EN | 20  
24. Glossary of Terms  
Table 15: Glossary of Terms  
Term  
Description  
24-Hour Zones  
A monitored input programmed to trigger an alarm condition when violated when  
the system is armed or disarmed 24 hours a day.  
Alarm Condition  
Your alarm system is armed and one of the detection devices is violated. A 24-hour  
zone (such as a smoke detector) can activate an alarm condition when your system  
arms or disarms.  
Answering Machine  
Bypass  
Answering machine bypass is incorporated. You can connect to the system for  
remote arming operations when there is an answering machine or facsimile machine  
on the same telephone line.  
Armed  
The system is in a ready state to accept alarms.  
Automatic Arming  
The system automatically arms at the same time every day in AWAY Mode or STAY  
Mode 1.  
Automatic Disarming  
AWAY Mode  
Codepad  
The system automatically disarms at the same time every day.  
Used to arm your system when you leave your premises.  
Arm/disarm the system and carry out other functions such as adding and deleting  
system user codes.  
Day Alarm  
Detectors  
Monitor a combination of zones while the system is disarmed.  
Devices connected to your alarm system used to detect intrusion and cause an  
alarm condition. Some forms of detection devices include Passive Infrared (PIR),  
smoke detectors, photoelectric beams, reed switches, and vibration sensors.  
Disarmed  
A state that does not accept alarms except on zones programmed for 24-hour  
operation.  
Dynamic Battery  
Testing  
Used to monitor and test the condition of your back-up battery.  
Entry Time/  
Entry Delay  
The time allowed by a zone for disarming the system after entering your premises.  
External Equipment  
Forced Arming  
Any device connected to your system such as detectors, codepads, and sirens.  
A situation where your alarm system can be armed when one or more zones are  
unsealed.  
Handover Delay  
The system is armed and a zone programmed for delay was violated. The delay zone  
hands over the remaining delay time to a zone programmed as handover. The  
handover zone does not activate an alarm until the remaining delay time expires. A  
handover zone acts as an instant zone if violated before the delay zone.  
Hand Held Remote  
Control  
Used to remotely operate your system by hand held transmitters.  
Isolating  
Manually disable (isolate) one or more zones before arming the system.  
Master Code  
A numeric code used to arm and disarm the system and to allow access to  
functions such as adding and deleting user codes.  
Monitoring Station  
A secure location where a digital receiver monitors numerous alarm systems and  
deciphers their Alarm Transmission Reports. The operator can then advise the  
appropriate authorities to take immediate action.  
Panic Alarm  
Sealed  
Type of alarm that indicates to the monitoring station there is an emergency  
situation at your premises.  
Refers to zone status. If a zone is sealed, the detection device is not violated and  
the zone indicator does not display on the codepad.  
Sensor Watch  
The control panel can recognise that detection devices may have stopped working  
or that the view to a PIR detector is blocked (unable to detect any movement over  
the duration of the time programmed by your installer).  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 24. Glossary of Terms  
EN | 21  
Table 15: continued  
Term  
Description  
Silent Alarm  
Your installer may program zones for silent operation. When the zone programmed  
for silent operation is violated during the armed period, your alarm system  
communicates with the monitoring station without sounding the sirens.  
STAY Mode 1  
A condition that automatically isolates zones when your system is armed in STAY  
Mode 1. Only your installer can program zones to be isolated automatically in STAY  
Mode 1.  
STAY Mode 2  
A condition that automatically isolates zones when your system is armed in STAY  
Mode 2. Only the Master Code holder can program zones to be isolated  
automatically in STAY Mode 2.  
Telco Arm Sequence  
Telco arming is a feature that automatically calls the telephone exchange and diverts  
your telephone number to another telephone when the system is armed in AWAY  
Mode. (In Australia, this feature is called “Call Forward”.)  
Telco Disarm  
Sequence  
Telco disarming automatically calls the telephone exchange and does not forward  
your telephone number.  
Unsealed  
User Code  
Zones  
Refers to zone status. A zone is unsealed when a zone is violated. The  
corresponding zone indicator displays on the codepad.  
The personal identification number that the operator uses to arm and disarm the  
system.  
A monitored input used to trigger an alarm condition when violated.  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 25. Installation Notes  
EN | 22  
25. Installation Notes  
Company Name  
Technician’s Name  
Technician’s Telephone Number  
Installation Date  
Warranty Expires  
Panel Software Version  
Service Notes  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 25. Installation Notes  
EN | 23  
Zone Description  
Describe each zone and mark the zones that are programmed to be automatically isolated in STAY Mode 1  
or are programmed for day alarm operation.  
Isolated In  
STAY Mode 1  
Day Alarm  
Enabled  
Zone 1  
Zone 2  
Zone 3  
Zone 4  
Zone 5  
Zone 6  
Zone 7  
Zone 8  
User Code Names  
Master  
Code  
Default = 2580  
User Code 1  
User Code 2  
User Code 3  
User Code 4  
User Code 5  
User Code 6  
User Code 7  
User Code 8  
Y
User Code 9  
User Code 10  
User Code 11  
User Code 12  
User Code 13  
User Code 14  
User Code 15  
User Code 16  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | 25. Installation Notes  
EN | 24  
Entry/Exit Times  
Entry Timer 1  
Exit Time  
Entry Timer 2  
Entry Guard Time  
Arming Options  
YES  
YES  
NO  
NO  
YES  
YES  
NO  
NO  
Single Button Arming  
Forced Arming  
Single Button Disarming  
Remote Arming By Telephone  
YES  
YES  
NO  
NO  
Automatic Arming (AWAY Mode)  
Automatic Arming (STAY Mode)  
Automatic Arming Time  
AM/PM  
AM/PM  
Automatic Disarming Time  
Output Descriptions  
Output 1  
Output 3  
Output 4  
Output 2  
Isolating Method  
YES  
YES  
NO  
NO  
Standard Isolating  
Code To Isolate  
Communication Options  
YES  
NO  
Back To Base Reporting  
YES  
NO  
Domestic Reporting  
Domestic Reporting – Number Of Beeps  
Other System Information  
Siren Run Time  
Minutes  
Sensor Watch Time  
Increments in Days  
YES  
NO  
Can Your System Be Serviced By Another Technician  
If Yes, Installer’s Code  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | Index  
EN | 25  
Index  
24-Hour Zones 20  
D
A
Date and Time 12  
Day Alarm 15  
Deleting Radio User Codes  
AC Mains Fail 12  
Adding Radio User Codes  
9
9
Adding User Codes  
Alarm Condition  
Alarms  
Duress .................................................................... 10  
Fire ......................................................................... 11  
Medical .................................................................. 11  
Panic....................................................................... 10  
Tamper (Access Denied)...................................... 11  
Answering Machine Bypass  
Area Display Indicators 17  
Area On/Off Indicators 17  
Armed 20  
9
20  
Deleting User Codes  
9
Detectors  
Disarmed  
Disarming  
20  
20  
9
Domestic Dialling  
16  
Acknowledging Domestic Calls...........................16  
Disable....................................................................16  
Programming Domestic Telephone Numbers ...16  
Duress Alarm 10  
20  
E
E2 Fault  
Entry Delay/Entry Time20  
Entry Guard Timer  
Event Memory Recall 15  
12  
Arming  
8
AWAY Mode.......................................................... 8  
STAY Mode 1......................................................... 8  
STAY Mode 2......................................................... 8  
Telephone Arming ............................................... 15  
Audible Indications  
Automatic Arming  
Automatic Disarming  
AUX Indicator 17  
AWAY Indicator  
External Equipment  
20  
F
Fault Analysis 12  
Fault Description  
7
20  
20  
AC Mains Fail .......................................................12  
Battery Fail.............................................................12  
Communication Fail .............................................12  
Date and Time.......................................................12  
E2 Fault..................................................................12  
Fuse Fail .................................................................12  
Horn Speaker Fail.................................................12  
Sensor Watch Fail .................................................12  
Telephone Line Fail..............................................12  
6
AWAY Mode 8, 20  
B
Battery Fail  
12  
Battery Testing 20  
Bell Test  
Codepad  
14  
C
Fault Descriptions  
12  
20  
Communciation Fail .............................................12  
System Fault...........................................................12  
Duress Alarm ........................................................ 10  
Fire Alarm ............................................................. 11  
Medical Alarm ...................................................... 11  
Panic Alarm........................................................... 10  
Tamper Alarm....................................................... 11  
Codepad Indicators  
FAULT Indicator  
7, 17  
Features  
Fire Alarm  
5
11  
Forced Arming 8, 20  
Fuse Fail 12  
Audible Indications ................................................ 7  
AWAY Indicator .................................................... 6  
FAULT Indicator.................................................... 7  
MAINS Indicator.................................................... 6  
Off Indicator............................................................ 7  
On Indicator............................................................ 7  
STAY Indicator....................................................... 6  
System Disarmed.................................................... 6  
Zone Indicators....................................................... 6  
H
Hand Held Remote Control  
20  
Handover Delay  
Horn Speaker Fail  
Horn Speaker Test  
20  
12  
14  
I
Isolating  
20  
Isolating Zones 11  
Code to Isolate ......................................................11  
Standard Isolating .................................................11  
Communciation Fail  
Communication Fail  
12  
12  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | Index  
EN | 26  
STAY Mode 1 8, 21  
M
Entry Guard Timer.................................................8  
STAY Mode 2 8, 21  
MAINS Indicator  
Master Code 20  
6, 17  
Master Partitioned Codepad Indicators 17  
Medical Alarm 11  
Entry Guard Timer.................................................8  
Programming Zones................................................9  
Monitoring Station  
20  
Strobe Indications  
10  
Strobe Test  
System Disarmed  
14  
O
6
Off Indicator  
On Indicator  
7
7
T
Operating From A Master Partitioned Codepad  
Tamper Alarm 11  
Telco Arm Sequence  
Telco Disarm Sequence 21  
Telephone Line Fail 12  
17  
13, 21  
Operating From Area Addressable Codepads  
17  
Test Report  
Testing  
14  
P
Pager Reporting18  
Bell Test..................................................................14  
Horn Speaker Test................................................14  
Strobe Test.............................................................14  
Test Report ............................................................14  
Walk Test...............................................................14  
Panic Alarm  
PARTIAL Indicator  
Partitioning 17  
10, 20  
17  
R
Radio User Codes  
Adding ..................................................................... 9  
U
Deleting.................................................................... 9  
Remote Arming 15  
Unsealed  
User Codes  
21  
21  
Remote Control20  
Adding......................................................................9  
Adding Radio Users................................................9  
Deleting....................................................................9  
S
Sealed 20  
Sensor Watch 20  
Sensor Watch Fail  
W
12  
Walk Test  
14  
Silent Alarm  
21  
Speaker Beeps 10  
Status Indicators17  
STAY Indicator 6  
Z
Zone Indicators 6, 17  
Zones 21  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
CC408 | Operators Guide | Notes  
EN | 27  
Notes:  
Bosch Security Systems | 5/04 | 920050O.OG.112  
 
Bosch Security Systems  
25 Huntingwood Drive  
Huntingwood NSW 2148  
Australia  
Phone: +612 9672 1777  
Facsimile: +612 9672 1717  
© 2003 Bosch Security Systems  
S1920050  
Issue 112  
4998152467B  
 

Blaupunkt Car Stereo System RCR 148 User Manual
Blodgett Hot Beverage Maker KTT E Series User Manual
Boston Acoustics Car Speaker boston mobile audio performance standard coaxial speakers User Manual
Bowers Wilkins Speaker DM640i User Manual
Braun Electric Shaver Series7 User Manual
Carrier Furnace 58MTB User Manual
Casio Calculator fx 9860G SD User Manual
Casio Musical Toy Instrument CGP700 User Manual
Cateye Heart Rate Monitor MSC Download Kit User Manual
Cisco Systems Conference Phone CP9951CCAMK9 User Manual