Bosch Appliances Home Security System LTC 9213 01 User Manual

LTC 9213/01, LTC 9225/00  
Instruction Manual  
EN Pole Mount Adaptors  
 
|
LTC 9213/01, LTC 9225/00 | Instruction Manual | Safety Precautions  
EN  
3
Safety Precautions  
For Indoor Product  
1. Water and Moisture - Do not use this unit near  
water - for example, in a wet basement, in an  
unprotected outdoor installation or in any area  
classified as a wet location.  
CAUTION: TO REDUCE THE RISK OF  
2. Object and Liquid Entry - Never push objects of  
any kind into this unit through openings, as they  
might touch dangerous voltage points or create  
short circuits, resulting in a fire or electrical  
shock. Never spill liquid of any kind on the unit.  
3. Power Cord and Power Cord Protection - For  
units intended to operate with 230VAC, 50Hz,  
the input and output power cord must comply  
with the latest versions of IEC Publication 227 or  
IEC Publication 245.  
ELECTRIC SHOCK, DO NOT REMOVE COVER  
(OR BACK). NO USER SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
This symbol indicates the presence of  
uninsulated dangerous voltage within the  
product s enclosure that can cause an electric  
shock.  
This symbol indicates the presence of  
important operating and maintenance  
(servicing) instructions in the literature  
accompanying the appliance.  
Power supply cords should be routed so they are  
not likely to be walked on or pinched. Pay  
particular attention to location of cords and plugs,  
convenience receptacles, and the point of exit  
from the appliance.  
Installation should be performed by qualified  
service personnel only in accordance with the  
National Electrical Code or applicable local  
codes.  
4. Overloading - Do not overload outlets and  
extension cords; this can result in a risk of fire or  
electrical shock.  
Power Disconnect. Units with or without  
ON-OFF switches have power supplied to the  
For Outdoor Product  
unit whenever the power cord is inserted into the  
power source; however, the unit is operational  
only when the ON-OFF switch is in the ON  
position. The power cord is the main power  
disconnect for all units.  
Power Lines - An outdoor system should not be  
located in the vicinity of overhead power lines,  
electric lights or power circuits, or where it may  
contact such power lines or circuits. When  
installing an outdoor system, extreme care should  
be taken to keep from touching power lines or  
circuits, as this contact might be fatal. U.S.A.  
models only - refer to the National Electrical  
Code Article 820 regarding installation of CATV  
systems.  
For Rack-mount Product  
1. Ventilation - Do not place this equipment in a  
built-in installation or rack, unless proper  
ventilation is provided, or the manufacturer’s  
instructions were followed. The equipment must  
not exceed its maximum operating temperature  
requirements.  
2. Mechanical Loading - When rack-mounting the  
equipment, ensure that a hazardous condition is  
not created by uneven mechanical loading.  
Bosch Security Systems, Inc. | December 23, 2008  
 
|
LTC 9213/01, LTC 9225/00 | Instruction Manual | Safety Precautions  
EN  
4
Precauciones de Seguridad  
Securite  
Attention : l’installation doit exclusivement Œtre rØalisØe par du  
PRECAUCI N: PARA DISMINUIR EL RIESGO DE DESCARGA  
ATTENTION : POUR VITER TOUT RISQUE D’ LECTROCUTION,  
N’ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU  
ARRI¨RE). CET APPAREIL NE CONTIENT AUCUN COMPOSANT  
SUSCEPTIBLE D’ TRE R PAR PAR L’UTILISATEUR. CONFIEZ  
LA R PARATION DE L’APPAREIL DU PERSONNEL QUALIFI .  
EL CTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE  
POSTERIOR). NO EXISTEN PIEZAS DE RECAMBIO EN EL  
INTERIOR DEL EQUIPO. EL PERSONAL DE SERVICIO  
CUALIFICADO SE ENCARGA DE REALIZAR LAS  
REPARACIONES.  
Ce symbole signale que le produit renferme une « tension  
potentiellement dangereuse » non isolØe susceptible de  
provoquer une Ølectrocution.  
Este s mbolo indica que existen puntos de tensi n peligrosos  
sin aislamiento dentro de la cubierta de la unidad. Estos  
puntos pueden constituir un riesgo de descarga elØctrica.  
Ce symbole invite l’utilisateur consulter les instructions  
d’utilisation et d’entretien (dØpannage) reprises dans la  
documentation qui accompagne l’appareil.  
El usuario debe consultar las instrucciones de funcionamiento y  
mantenimiento (reparaci n) en la documentaci n que se  
suministra con el aparato.  
personnel qualifiØ, conformØment au code national d’ØlectricitØ  
amØricain (NEC) ou au code d’ØlectricitØ local en vigueur.  
Atenci n: la instalaci n la debe realizar œnicamente personal  
cualificado de conformidad con el National Electric Code o las  
normas aplicables en su pa s.  
Coupure de l’alimentation. Qu’ils soient pourvus ou non d’un  
commutateur ON/OFF, tous les appareils re oivent de l’Ønergie une  
fois le cordon branchØ sur la source d’alimentation. Toutefois,  
l’appareil ne fonctionne rØellement que lorsque  
le commutateur est rØglØ sur ON. Le dØbranchement du cordon  
d’alimentation permet de couper l’alimentation des appareils.  
Desconexi n de la alimentaci n. Las unidades con o sin  
interruptores de encendido/apagado reciben alimentaci n  
elØctrica siempre que el cable de alimentaci n estØ conectado a  
la fuente de alimentaci n. Sin embargo, la unidad s lo funciona  
cuando el interruptor estÆ en la posici n de encendido. El cable  
de alimentaci n es la principal fuente de desconexi n de todas  
las unidades.  
Veiligheidsmaatregelen  
Sicherheitshinweise  
VOORZICHTIG: OPEN DE BEHUIZING OF DE ACHTERKANT  
VAN HET APPARAAT NIET. ZO VERMINDERT U HET RISICO  
OP ELEKTRISCHE SCHOKKEN. IN HET APPARAAT  
BEVINDEN ZICH GEEN ONDERDELEN DIE U ZELF KUNT  
REPAREREN. LAAT SERVICE EN ONDERHOUD UITVOEREN  
DOOR GEKWALIFICEERD PERSONEEL.  
VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU  
VERMEIDEN, IST DIE ABDECKUNG (ODER R CKSEITE) NICHT  
ZU ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN DIESEM  
BEREICH, DIE VOM BENUTZER GEWARTET WERDEN K NNEN.  
LASSEN SIE WARTUNGSARBEITEN NUR VON QUALIFIZIERTEM  
WARTUNGSPERSONAL AUSF HREN.  
Dit symbool geeft aan dat er binnen in het apparaat  
onge soleerde, gevaarlijke spanning aanwezig is die mogelijk  
elektrische schokken kan veroorzaken.  
Das Symbol macht auf nicht isolierte gef hrliche Spannung"  
im Geh use aufmerksam. Dies kann zu einem elektrischen  
Schlag f hren.  
De gebruiker dient de bedienings- en onderhoudsvoorschriften  
te raadplegen in de documentatie die werd meegeleverd met  
het apparaat.  
Der Benutzer sollte sich ausf hrlich ber Anweisungen f r  
die Bedienung und Instandhaltung (Wartung) in den  
begleitenden Unterlagen informieren.  
Attentie: het apparaat mag alleen door gekwalificeerd personeel  
worden ge nstalleerd. De installatie dient in overeenstemming  
met de nationale elektrische richtlijnen of de van toepassing  
zijnde lokale richtlijnen te worden uitgevoerd.  
Achtung! Die Installation sollte nur von qualifiziertem  
Kundendienstpersonal gem jeweils zutreffender  
Elektrovorschriften ausgef hrt werden.  
Spanning uitschakelen. Apparatuur met of zonder  
Unterbrechung des Netzanschlusses. Ger te mit oder ohne  
Netzschalter haben Spannung am Ger t anliegen, sobald der  
Netzstecker in die Steckdose gesteckt wird. Das Ger t ist jedoch  
nur betriebsbereit, wenn der Netzschalter (EIN/AUS) auf EIN  
steht. Wenn das Netzkabel aus der Steckdose gezogen wird, ist  
die Spannungszuf hrung zum Ger t vollkommen unterbrochen.  
aan-uitschakelaar staat onder spanning zolang de stekker is  
aangesloten op de wandcontactdoos. De apparatuur is uitsluitend  
in werking als de aan-uitschakelaar aan staat. Het netsnoer is de  
"hoofdschakelaar" voor alle apparatuur.  
Bosch Security Systems, Inc. | December 23, 2008  
 
|
LTC 9213/01, LTC 9225/00 | Instruction Manual | Safety Precautions  
EN 5  
Sicurezza  
ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE  
ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL  
PANNELLO POSTERIORE). L’UNIT NON CONTIENE  
COMPONENTI INTERNI RIPARABILI DALL’UTENTE. PER  
QUALSIASI INTERVENTO,, RIVOLGERSI A PERSONALE  
TECNICO QUALIFICATO.  
Questo simbolo indica la presenza di "tensione pericolosa" non  
isolata all’interno del contenitore del prodotto. Ci comporta un  
potenziale rischio di scosse elettriche.  
Si consiglia di consultare le istruzioni operative e di  
manutenzione (interventi tecnici) contenute nella  
documentazione fornita con il dispositivo.  
Attenzione: l’installazione deve essere effettuata esclusivamente  
da personale tecnico qualificato in conformit con il National  
Electrical Code o con le normative locali vigenti.  
Scollegamento dell’alimentazione. Le unit dotate o sprovviste di  
interruttori ON-OFF vengono alimentate quando si inserisce il  
cavo nella presa dell’alimentazione. L’unit tuttavia in funzione  
solo quando l’interruttore ON-OFF si trova nella posizione ON. Il  
cavo di alimentazione costituisce il dispositivo di scollegamento  
dell’alimentazione principale per tutte le unit .  
Medidas de Seguranc a  
CUIDADO: PARA REDUZIR O RISCO DE CHOQUE  
EL CTRICO, NˆO RETIRE A TAMPA (OU A PARTE  
POSTERIOR). NO INTERIOR, NˆO EXISTEM PE AS QUE  
POSSAM SER REPARADAS PELO UTILIZADOR. REMETA A  
ASSIST NCIA PARA OS T CNNICOS QUALIFICADOS.  
Este s mbolo indica a presen a de "tens o perigosa" n o isolada  
dentro da estrutura do produto, o que pode constituir risco de  
choque elØctrico.  
O utilizador deve consultar as instru ıes de funcionamento  
e manuten o (assistŒncia) nos documentos que  
acompanham o aparelho.  
Aten o: a instala o deve ser executada apenas por tØcnicos  
qualificados da assistŒncia, de acordo com o c digo elØctrico  
nacional ou os c digos locais aplicÆveis.  
Corte de corrente. As unidades com ou sem interruptores  
ON-OFF (ligar/desligar) recebem corrente sempre que o fio de  
alimenta o estÆ introduzido na fonte de alimenta o; contudo, a  
unidade apenas estÆ operacional quando o interruptor ON-OFF  
estÆ na posi o ON. O fio de alimenta o destina-se a desligar a  
corrente em todas as unidades.  
Bosch Security Systems, Inc. | December 23, 2008  
 
|
LTC 9213/01, LTC 9225/00 | Instruction Manual | Unpacking  
EN 6  
1.0 UNPACKING  
3.0 DESCRIPTION  
This equipment should be unpacked and handled with  
care. If an item appears to have been damaged in  
shipment, notify the shipper.  
The LTC 9213/00 and LTC 9225/00 Pole Mount  
Adapters are designed to permit the installation of  
indoor/outdoor wall mounts to a pole capable of  
supporting the total weight of equipment installed. The  
pole can range from 76 mm (3 in.) to 381 mm (15 in.)  
in diameter.  
Verify that all parts shown in the Parts List have been  
included. If any items are missing, notify your Bosch  
Security Systems Sales or Customer Service  
Representative.  
4.0 INSTALLATION  
The original packing carton is the safest container in  
which to transport the unit. Save it for possible future use.  
WARNING: This installation should be made  
by a qualified service person and conform to  
all local codes.  
1.1 Parts List  
Qty Item  
4.1 Mount Compatibility  
Pole Mount Suggested  
Maximum  
1
1
1
1
Unit (verify model number)  
This installation manual  
Adapter  
Wall Mounts  
Rated Load  
LTC 9213/01 LTC 9212/00  
9 kg (20 lb)  
LTC 9215/00  
9 kg (20 lb)  
BAND-ITTool instruction chart  
Mounting bracket  
LTC 9215/00S 9 kg (20 lb)  
LTC 9225/00 LTC 9216/00  
45 kg (100 lb)  
90 kg (200 lb)  
LTC 9222/00  
LTC 9213/01 Hardware kit  
Structural band strap, 3 m (10 ft)  
Screw, hex head, M8 x 25  
Washer, spiral lock, M8  
1
4
4
4
4.2  
4.2.1  
Tools Required  
LTC 9213/01 Pole Mount Adapter  
8 mm Hex wrench  
Screw, oval head, # 6-32  
Banding tool (TC9311PM3T is recommended)  
LTC 9225/00 Hardware kit  
1
Structural band strap, 3 m (10 ft), that must be cut into  
two (2) 1.5 m (5 ft) lengths  
4.2.2 LTC 9225/00 Pole Mount Adapter  
12 mm Hex wrench  
2
6
6
6
6
Band buckle  
Banding tool (TC9311PM3T is recommended)  
Screw, hex head, M12 x 35  
Nut, hex, M12  
4.3  
Mounting  
Washer, spiral lock, M2  
Washer, plain, M12  
1. Cut the structural band strap into two (2) 1.5 m  
(5 ft) straps.  
2.0 SERVICE  
2. Attach the bracket to the pole at the band  
desired height using the two (2) straps and the  
two (2) buckles provided.  
If the unit needs servicing, contact the nearest Bosch  
Security Systems Service Center for authorization to  
return and shipping instructions.  
3. Tension the straps according to the instructions  
for the banding tool used. Banding tool,  
TC9311PM3T, is recommended and may be  
purchased separately. A BAND-ITTool  
instruction chart is provided with each pole  
mount. The ends of the bands are bent around  
the buckle (see Figure 1).  
Service Centers  
USA  
Phone:  
Fax:  
800-366-2283 or 717-735-6638  
800-366-1329 or 717-735-6639  
CCTV Spare Parts  
Phone:  
Fax:  
800-894-5215 or 408-956-3853 or 3854  
408-957-3198  
E-mail:  
Canada  
Phone:  
514-738-2434  
Tension and  
Europe, Middle East & Asia Pacific Region  
Phone: 32-1-440-0711  
For additional information, see  
Bend Back Bands  
Bend Buckle  
Tab Over Bands  
Figure 1: Bending Method  
Bosch Security Systems, Inc. | December 23, 2008  
 
|
LTC 9213/01, LTC 9225/00 | Instruction Manual | Installation  
EN 7  
4. For model LTC 9213/01 with an LTC 9212/00,  
LTC 9215/00, or an LTC 9215/00S, secure the  
wall mount to the pole mount using the four (4)  
8 mm screws and lock washers provided. Use  
the four larger holes that are in a square pattern  
around the center (see Figure 2).  
5.0 SPECIFICATIONS  
5.1 LTC 9213/01, LTC 9225/00  
Pole Mount Adapters  
Construction: Formed aluminum plate  
Finish: Light gray  
Weight:  
LTC 9213/01: 0.5 kg (1 lb)  
LTC 9225/00: 1.4 kg (3 lb)  
Pole Mount  
Wall Mount  
LTC 9213/01 Pole Mount Adaptor  
Band  
Buckle  
6-32 Thread  
Typ 4 Places  
M8 Thread  
53.3  
(2.10)  
Typ 4 Places  
Lock Washer  
Screw  
139.1  
ÿ
38.4 Hole  
(1.51)  
(5.48)  
Figure 2: Securing the LTC 9213/01 with an  
LTC 9212/00, LTC 9215/00 or an  
LTC 9215/00S  
66.5  
(2.62)  
45.8  
49.4  
(1.81)  
(1.95)  
5. For model LTC 9213/01 with an LTC 1348/00,  
secure the wall mount to the pole mount using  
the four (4) No. 6 screws provided. Use the four  
(4) smaller holes that are in a rectangular  
pattern.  
49.4  
(1.95)  
82.9  
mm  
(in.)  
(3.27)  
152.4  
(6.00)  
6. For model LTC 9225/00 with an LTC 9216/00  
or an LTC 9222/00, secure the wall mount to  
the pole mount using the six (6) 12 mm screws,  
plain washers, lock washers and nuts provided  
(see Figure 3).  
LTC 9225/00 Pole Mount Adaptor  
203  
8.00  
102  
52  
2.04  
4.00  
14  
0.56  
54  
2.13  
Pole Mount  
6
32  
0.25  
1.25  
67  
2.64  
Wall Mount  
Band  
165  
6.50  
Buckle  
Nut  
Lock Washer  
Plain Washer  
Screw  
337  
13.25  
Figure 3: Securing the LTC 9225/00 with an  
LTC 9216/00 or an LTC 9222/00  
mm  
in  
76  
3.00  
152  
6.00  
Bosch Security Systems, Inc. | December 23, 2008  
 
Americas  
Bosch Security Systems  
130 Perinton Parkway  
Fairport, New York, 14450, USA  
Phone: +1 (585) 223 4060  
+1 800 289 0096  
Europe, Middle East, Africa  
Bosch Security Systems B.V.  
P.O. Box 80002  
5600 JB Eindhoven, The Netherlands  
Phone: +31 (0) 40 27 83955  
Asia-Pacific  
Bosch Security Systems Pte Ltd  
38C Jalan Pemimpin  
Singapore 577180  
Phone: +65 6319 3450  
Fax:  
+31 (0) 40 27 86668  
Fax:  
+65 6319 3499  
' 2008 Bosch Security Systems GmbH  
F01U122758 | Updated December 23, 2008 | Data subject to change without notice.  
BAND-ITis a registered trademark of Idex Corporation.  
 

Blackberry Network Card MAT 17698 001 User Manual
Black Box Network Router 39004 User Manual
Black Box Surge Protector SP075A User Manual
Bosch Appliances Home Security System VIPX 1600X FM4 User Manual
Bowers Wilkins Portable Speaker CDM CSE User Manual
Braun Electric Shaver 5 720 User Manual
Briggs Stratton Portable Generator PRO10000 030383 User Manual
Brinkmann Gas Grill 4 Burner Gas Grill Grill User Manual
Carrier Air Conditioner 50MH User Manual
Carrier Heat Pump 50RHC User Manual