Bushnell Telescope 78 6000 User Manual

VOYAGER® 6 INCH DOBSONIAN TELESCOPE  
MODEL 78-6000  
9
8
1
2
3
7
6
4
5
1. Rack & Pinion focusing System  
2. Reflector Body  
6. Carry Handle  
7. Primary Mirror  
8. Finderscope  
3. Altitude Bearing  
4. Dobsonian Side Panel  
5. Dobsonian Base (Azimuth Bearing)  
9. 1.25" Format Eyepiec  
e
Never Look Directly At The Sun With Your Telescope  
Permanent Damage To Your Eyes May Occur  
 
7. Locate the circular component with the five drilled holes. This component is called the  
azimuth bearing plate. Identify the side with the four outer countersunk holes like on the  
other components. The side with the holes countersunk is the underside.  
8. Insert the remaining four screws through the azimuth bearing plate from the underside into  
the corresponding pre-drilled holes in the bottom edges of the side panels on the previously  
assembled "box" as shown in the diagram.  
9. Take the assembled "box" and azimuth bearing plate and turn it on its side. Locate the  
remaining circular component called the bottom plate and the remaining hardware.  
10. Take the bottom plate with rubber feet facing out and line it up with the hole in the center of  
the azimuth bearing plate of the assembled "box"/azimuth bearing plate combination.  
11. Insert the Nylon center bearing tube through the hole. Place a flat washer on each side.  
Insert the Center Bolt from the bottom side and attach the hex nut on the top side. Tighten  
enough to hold the base together yet loose enough to allow the base to turn easily.  
Note: Your Bushnell Voyager Dobsonian Telescope Body comes pre-assembled from the  
factory. No installation other than what is listed below is required.  
ATTACH FINDERSCOPE AND TELESCOPE  
1. Remove Reflector Telescope Body (2) and Finderscope (8) from carton.  
2. Remove nuts located near the Rack & Pinion Focusing Mechanism (1) on Reflector Telescope  
Body (2).  
3. Attach Finderscope (8) to Reflector Telescope Body (2) by inserting the screws extending  
from the Reflector Telescope Body (2) into the holes in the base of the Finderscope (8).  
4. Refasten nuts so that Finderscope (8) is secure.  
5. Take Reflector Telescope Body (2) with attached Finderscope (8) and set them into the  
Dobsonian base making certain that the Altitude Bearings (3) come to rest in the semi-circle  
cradles on the side panels of the Dobsonian base. Note: The Finderscope (8) should be on  
top of the Reflector Telescope Body (2) and the Bushnell® logo should be upright.  
6. Move the Dobsonian Telescope Assembly in both directions (up and down, and left and  
right) to become familiarized with the unit. If the telescope doesn't move smoothly, review  
the assembly process to verify you performed the assembly correctly.  
THE FINAL STEPS  
1. Remove 1.25" Format Eyepiece (9) from carton.  
2. Insert into Rack & Pinion Focusing Mechanism (1).  
3. Remove Protective Dust Cover from end of telescope nearest the Rack & Pinion Focusing  
Mechanism (1).  
4. Let the adventure begin.  
Your Bushnell Telescope is now ready to be used. To obtain the fullest enjoyment from your  
telescope, please refer to the following additional information.  
Astronomical Telescopes are designed in such a way that the image you will see appear will be  
UPSIDE DOWN and REVERSED, this is acceptable for viewing celestial bodies.  
 
TELESCOPE USE  
SELECTING AN EYEPIECE:  
1. You should always start viewing with the lowest power eyepiece, which in this case is the 25  
mm lens. Note: the base power of each eyepiece is determined by the focal length of the  
telescope objective element, which for this model is 1000 mm. A formula can be used to  
determine the power of each eyepiece: telescope OBJECTIVE mirror focal length  
EYEPIECE focal length = MAGNIFICATION (e.g. Using the 25 mm lens, the calculation  
would look like this: 1200 mm ¸ 25mm = 48x or 48 power.)  
2. Offered as an accessory for this telescope is a Barlow lens (model #78-0105). Barlow lenses  
are used to double or triple the power of your telescope by placing your Barlow between the  
focusing tube and the eyepiece. Using the example above, a 2x Barlow lens would give you a  
total power of 96x or 96 power. (48 x 2 = 96x or 96 power). Other accessories available  
include a 9mm eyepiece (model #78-0101) that would give you 133x or 133 power or 266x  
when used in conjunction with the Barlow accessory and a standard camera adapter (model  
#78-0104) for photographing the night sky.  
FOCUSING TELESCOPE:  
1. After inserting the eyepiece, aim the main telescope tube at a land-based target at least 200  
yards away (e.g. A telephone pole or building). Fully extend focusing tube by turning Rack &  
Pinion Focusing Mechanism (1)  
2. While looking through selected eyepiece (in this case the 25 mm), slowly retract focusing  
tube by turning Rack & Pinion Focusing Mechanism (1) until object comes into focus.  
ALIGNING FINDERSCOPE:  
1. Look through low-power 1.25" format eyepiece (9) and establish a well-defined target (see  
focusing telescope section).  
2. Looking through Finderscope (8), alternate tightening each Finderscope Adjustment Screw  
surrounding the Finderscope (8) in the Finderscope Mount until crosshairs of Finderscope (8)  
are precisely centered on the same object already centered in Main Telescope Tube's field of  
view as seen through the 1.25" Format Eyepiece (9).  
3. Now, objects located first with the Finderscope (8) will be centered in the field of view of the  
main telescope as seen through the 1.25" Format Eyepiece (9).  
COLLIMATING THE TELESCOPE  
Good alignment or collimation of the telescope's optical components will guarantee the most  
optimum viewing. This telescope body comes preassembled from the factory and  
precollimated. Therefore collimation should not be required. However, due to its great  
importance there are a few steps that you can take to ensure that your telescope is properly  
collimated.  
1. Remove the 1.25" Format Eyepiece (9) from the Rack and Pinion Focusing Mechanism (1).  
2. Look into the Rack and Pinion Focusing Mechanism (1) with the eyepiece removed. You will  
see the secondary mirror located a few inches inside the end of the telescope tube (nearest the  
Rack and Pinion Focusing Mechanism). Since it is a mirror, you will see a reflection of the  
large primary mirror (7). That mirror will show an image of the secondary mirror and your  
eye. Each image will be centered in a concentric set of images starting with the image of the  
Primary Mirror (7), the secondary mirror, and your eye.  
3. Please refer to the diagram to see what to expect.  
 
4. If the image of your eye is centered in the reflection of the secondary mirror, your secondary  
mirror is collimated. If it is off to one side, then secondary mirror adjustment will be  
required. By removing the plastic cap on the secondary mirror base at the end of the  
telescope tube nearest the Rack and Pinion Focusing Mechanism (1), you will see three screw  
heads. They are positioned 120 degrees apart. By adjusting these three screws very slowly  
and carefully, the secondary mirror will reflect an image of your eye that is perfectly centered  
in the reflection of the secondary mirror. Once this is accomplished replace the plastic cap.  
Your secondary mirror is now collimated.  
5. Once secondary mirror collimation is confirmed, you will need to verify Primary Mirror (7)  
collimation. If the image of the secondary mirror is centered in the reflection of the primary  
mirror, then your primary mirror is collimated. If it is off to one side, then Primary Mirror (7)  
adjustment will be required. By locating the Primary Mirror (7) you will see three screw  
heads on the bottom end of the telescope furthest from the Rack and Pinion Focusing  
Mechanism (1). They are alsopositioned 120 degrees apart. By adjusting these three screws  
very slowly and carefully, the Primary Mirror (7) will reflect an image of the secondary  
mirror that is perfectly centered in the reflection of the Primary Mirror (7). Once this is  
accomplished your Primary Mirror (7) is now collimated.  
6. Your telescope is now ready to deliver the best images possible.  
Enjoying Your New Telescope  
1. First determine your targeted object. Any bright object in the night sky is a good starting  
point. One of the favorite starting points in astronomy is the moon. This is an object sure to  
please any budding astronomer or experienced veteran. When you have developed  
proficiency at this level, other objects become good targets. Saturn, Mars, Jupiter, and Venus  
are good second steps to take.  
2. The first thing you need to do after assembling the telescope as planned is center the desired  
object in the finderscope's cross hairs. Provided you did a reasonable job aligning the  
finderscope, a quick look through the main telescope tube at low power should reveal the  
same image. With the lowest power eyepiece (the one with the largest number printed on it)  
you should be able to focus the same image that you saw through the finderscope. Avoid the  
temptation to move directly to the highest power. The low power eyepiece will give you a  
wider field of view, and brighter image--thus making it very easy to find your target object.  
At this point with a focused image in both scopes, you've passed the first obstacle. If you  
don't see an image after attempting to focus it in, you might consider aligning your  
finderscope again. Once you pass this step, you'll will enjoy the time spent ensuring a good  
alignment. Every object you center in the finderscope will be easily found in the main  
telescope tube, which is important for continuing your exploration of the night sky.  
3. The low power eyepieces are perfect for viewing the full moon, planets, star clusters, nebulae,  
and even constellations. These should build your foundation. However, for more detail, try  
bumping up in magnification to higher power eyepieces on some of these objects. During  
calm and crisp nights, the light/dark separation line on the moon (called the "Terminator") is  
marvelous at high power. You can see mountains, ridges and craters jump out at you due to  
the highlights.  
Similarly, you can move up to higher magnifications on the planets and  
nebulae. Star clusters and stars are best viewed through the low power no matter what.  
 
4. The recurring astronomical theater we call the night sky is an ever-changing billboard. In  
other words, not the same movie plays all the time. Rather, the positions of the stars change  
not only hourly as they seem to rise and set, but also throughout the year. As the earth orbits  
the sun our perspective on the stars changes on a yearly cycle about that orbit. The reason  
the sky seems to move daily just as the sun and the moon "move" across our sky, is that the  
earth is rotating about its axis. As a result you may notice that after a few minutes or a few  
seconds depending on what power you are viewing at, the objects in your telescope will  
move. At higher magnifications especially, you will notice that the moon or Jupiter will  
"race" right out of the field of view. To compensate, just move the fine adjustment controls  
on your telescope to "track" it in the necessary path.  
Helpful Hints  
1. Your telescope is a very sensitive instrument. For best results and fewer vibrations set your  
telescope up on a level location on the ground rather than your concrete driveway or your  
wooden deck. This will provide a more stable foundation for viewing, especially if you've  
drawn a crowd with your new telescope.  
2. If possible view from a location that has relatively few lights. This will allow you to see  
much fainter objects. You'd be surprised how much more you'll see from your local lake or  
park when compared to a backyard in the city.  
3. Using your telescope out a window is NEVER recommended.  
4. View objects that are high in the sky if possible. Waiting until the object rises well above the  
horizon will provide a brighter and crisper image. Objects on the horizon are viewed  
through several layers of earth's atmosphere. Ever wonder why the moon appears orange as  
it sets on the horizon. It's because you are looking through a considerable more amount of  
atmosphere than you would directly overhead. (Note: If objects high in the sky are distorted  
or wavy, you are probably viewing on a very humid night.) During nights of unstable  
atmosphere, viewing through a telescope can be frustrating if not impossible. Astronomers  
refer to crisp, clear nights as nights of "good seeing."  
Where do I start?  
Your Bushnell telescope can bring the wonders of the universe to your eye. While this manual is  
intended to assist you in the set-up and basic use of this instrument, it does not cover everything  
you might like to know about astronomy. The first thing you need to do is get a very simple star  
chart and a flashlight with a red bulb or red cellophane over the end. For objects other than stars  
and constellations, a basic guide to astronomy is a must. Some recommended sources appear on  
our website at www.bushnell.com. Also on our website will be current events in the sky for  
suggested viewing. But, some of the standbys that you can see are:  
The Moon--a wonderful view of our lunar neighbor can be enjoyed with any magnification. Try  
viewing at different phases of the moon. Lunar highlands, lunar maria (lowlands called "seas"  
for their dark coloration), craters, ridges and mountains will astound you.  
Saturn--even at the lowest power you should be able to see Saturn's rings and moons. This is one  
of the most satisfying objects in the sky to see simply because it looks like it does in pictures.  
Imagine seeing what you've seen in textbooks or NASA images from your backyard!  
Jupiter--the largest planet in our solar system is spectacular. Most noted features are its dark  
stripes or bands both above and below its equator. These are the north and south equatorial  
belts. Also interesting are Jupiter's four major moons. Pay close attention to their positions from  
night to night. They appear to be lined up on either side of Jupiter.  
 
Mars--The Great Red Planet appears as a reddish-orange disk. Look at different times of the year  
and try to catch a glimpse of the white polar ice caps.  
Venus--just like the moon, Venus changed phases from month to month. Some views of brilliant  
Venus appear as if you were looking at a distant crescent moon.  
Nebulae--The Great Orion Nebula is a very well known night sky object. This and many others  
are brought to you by this telescope.  
Star Clusters--View millions of stars densely packed in a cluster that resembles a ball.  
Galaxies--One of the greatest and most interesting galaxies is our neighbor the Andromeda  
Galaxy. Enjoy this and many others. Much, much, more!  
ANSWERS TO COMMONLY ASKED QUESTIONS  
1. The image I see in the telescope is upside down and  
reversed from right to left ?  
·
An upside-down and reversed image is a  
common characteristic of most astronomical  
telescopes. Since telescopes are used for  
astronomical viewing orientation is not important.  
The image in the finderscope will also be upside  
down and reversed.  
2. How do I determine the power my telescope ?  
·
The power of your telescope can be determine  
by dividing the focal length of the objective lens by  
the focal length of the eyepiece. The eyepiece focal  
length is the number printed on the eyepiece. (For  
example: 1200 ¸ 25 = 48X)  
3. Where do I find the Telescope Focal Length  
·
The telescope focal length is the same focal  
length as the objective focal length. For this  
telescope it is 1200mm. Telescope focal lengths  
range from 600mm to 1200mm on Bausch & Lomb  
and Bushnell telescopes.  
4. What can I see with my telescope ?  
·
Telescopes with power ranging from 25X to  
50X can be used to view Star Clusters and Nebulae.  
90X to 120X telescope can view galaxies. Most  
planets can be seen at any magnification.  
5. What do the numbers on the eyepiece mean ?  
·
The numbers on the eyepiece represents the  
“focal Length” of the eyepiece.  
 
TROUBLESHOOTING GUIDE  
If after you have set-up your new telescope you are unable to see any objects, use this Quick  
Reference guide to help you to understand the cause of the problem and quickly determine a remedy  
1. I’ve completed the set-up yet I cannot see anything  
·
·
·
Check to see if objective lens cover and all  
other lens covers have been removed.  
Try to view an object that is 200 or more  
yards away.  
If there is more than one eyepiece included  
with the telescope, use the lowest power  
(highest number) eyepiece to begin viewing.  
·
Use the Rack & Pinion Focusing Mechanism to  
bring the object you are trying to view into  
focus  
 
Telescope LIFETIME LIMITED WARRANTY  
Your telescope is warranted to be free of defects in materials and workmanship for the lifetime  
of the original owner. The Lifetime Limited Warranty is an expression of our confidence in the  
materials and mechanical workmanship of our products and is your assurance of a lifetime of  
dependable service.  
If your telescope contains electrical components the electronic components are warranted to be  
free of defects in materials and workmanship for one year after the date of purchase.  
In the event of a defect under this warranty, we will, at our option, repair or replace the  
product, provided that you return the product postage prepaid. This warranty does not cover  
damages caused by misuse or improper handling, installation or maintenance of the product.  
Any return made under this warranty must be accompanied by the items listed below:  
1) A check in the amount of $15.00 to cover the cost of handling  
2) Name and address for product return  
3) An explanation of the defect  
4) Product should be well packed in a sturdy outside shipping carton to prevent  
damage in transit and return postage prepaid to the address listed below:  
IN U.S.A. Send To:  
Bushnell * 8500 Marshall Drive * Lenexa, Kansas 66214  
IN CANADA Send To:  
Bushnell * 25A East Pearce Street, Unit 1 * Richmond Hill, Ontario L4B 2M9  
For products purchased outside the United States and Canada please contact your local dealer  
for applicable warranty information. This warranty gives you specific legal rights. You may  
have other rights which vary from country to country.  
©2001 Bushnell Performance Optics  
 

Belkin Switch F1DK102UUK User Manual
Black Box Surge Protector SP361A R2 User Manual
Blue Rhino Charcoal Grill CBC830L C User Manual
Califone Headphones 3064AV User Manual
Cambridge Audio TV Converter Box azur DacMagic User Manual
Carrier Air Conditioner 09DK054 094 User Manual
Casio Watch 1794 User Manual
Casio Watch MA1301 EA User Manual
Cecilware Hot Beverage Maker Ready To Serve Dispensers User Manual
Chromalox Electric Heater PE417 3 User Manual