C Crane Portable Radio PR D4VW User Manual

INSTRUCTION MANUAL  
PLEASE READ ALL THE INSTRUCTIONS COMPLETELY  
BEFORE USE AND SAVE MANUAL FOR FUTURE  
REFERENCE.  
 
Table of Contents  
Button Identification ……………………….......................  
Getting Started  
4
Powering your Radio ............................................ 5  
Installing the batteries …………………………...... 6  
Display Panel ……………………………………......  
Setting The Clock ………………………………...... 8  
Setting The Alarm …………………………….........  
7
8
Snooze Feature ……………………………............. 10  
Sleep Timer ………………………………………..... 11  
Radio Operation  
Tuning ………………………………………….......... 12  
Weather Alert System ……………………….......... 13  
Tuning Steps ………………………………….......... 16  
Headphone and Audio Input Jacks ……..…….... 17  
Specifications ………………………………………............ 18  
Troubleshooting Guide ……………………....................... 19  
Radio Noise Troubleshooting …………………………..... 20  
Listening Tips ………………………………………............. 21  
Safety Instructions ……………………………….........…... 22  
 
Button Identification  
1
2
3
4
5
6
7
8
11  
10  
9
1) Power or Sleep Timer  
2) Band or Tuning Steps  
3) Radio Alarm Set  
7) Volume Control  
8) Tuning (Up/Down)  
9) Scan  
4) Beep Alarm Set  
10) Scan or Clock Set  
5) Display Clock/Frequency  
6) Weather Alert (3 Modes)  
11) Memory Presets (1-5)  
Note: When you see a next to a button on the radio, it means  
you must press and hold the button down for two seconds  
to activate the function. The appropriate symbol will then  
appear on the display along with sounding a beep.  
Page 4  
Sonido Radio  
 
Getting Started  
POWERING YOUR RADIO  
Before powering your radio be sure to read  
the Safety Instructions on pages 22 and 23.  
ƽ
The Sonido Radio will run on (4) Dsize NiMH or alkaline batter-  
ies or on 120V AC house current using the AC power adapter.  
Batteries are optional. If the AC power adapter is removed from  
the radio for more than three minutes, without batteries, you will  
lose clock, alarm and any memory settings. The Sonido will not  
charge batteries.  
AC POWER ADAPTER OPERATION  
Before you plug the AC power adapter into an outlet, be sure the  
AC voltage is 120Volts/60Hz. If you have batteries in the radio  
and you use the AC power adapter, the batteries will automatically  
be disconnected.  
NOTE: If you remove the power adapter without turning the radio  
OFF, the radio will automatically revert to the batteries.  
Insert the AC Power Adapter  
plug into the DC jack on the  
left side of the radio.  
NOTE: The AC adapter should be disconnected from the main  
supply when not in use for prolonged periods of time.  
Sonido Radio  
Page 5  
 
Getting Started  
INSTALLING THE BATTERIES  
1) Position the radio face down on a soft surface to protect it.  
2) Open the battery compartment cover on the rear of the unit  
by pressing the catch.  
3) Insert the (4) Dcell batteries into the compartment as ind-  
icated in the drawing below. Be sure the negative (-) end is  
against the spring. Refer to the drawing below to insure cor-  
rect installation of your batteries.  
4) Close the battery cover. You are now ready to operate your  
radio.  
Open battery cover by  
pressing the clip towards the  
bottom of the radio  
Fourth Battery  
Third Battery  
Second Battery  
First Battery  
BATTERY REPLACEMENT  
Symptoms of low batteries include: Distortion, a stuttering  
sound, flashing low battery sign, or Eappearing on the  
display.  
After removing dead batteries for replacement, you have at least  
5 minutes to replace the batteries before your clock and memory  
information will be lost (if the radio is not plugged in).  
This symbol means  
the batteries are full.  
This symbol means  
the batteries are low. batteries are dead.  
This symbol means the  
Page 6  
Sonido Radio  
 
Getting Started  
DISPLAY PANEL  
2
3
5
6
4
1
12  
11  
7
9
8
10  
1) Time Set  
7) Preset stations (1 - 5)  
8) Frequency Unit  
2) Battery Status Symbol  
3) Sleep Timer/Snooze  
Status  
9) Station Frequency /  
Clock Display  
4) Radio Alarm  
10) AM / PM Indicator  
11) Indicates Band In Use  
12) Stereo Reception  
5) Beep Tone Alarm  
6) Weather Alert Modes  
Sonido Radio  
Page 7  
 
Getting Started  
SETTING THE CLOCK  
Please read this entire section carefully before you start. The  
clock can be set either while the radio is on or off. You will need  
to go through the steps listed below without stopping for more  
than 15 seconds at any given time or you will have to start over.  
(Refer to page 4 for Button Identification.)  
1) Press and hold the Scan/Set Button for three  
seconds. You will hear a beep. The HOUR DIGIT  
and the  
symbol will flash on the display.  
2) Using the Up/Down Tuning Buttons, select the  
appropriate hour digit and AM or PM.  
SCAN  
3) Press the Scan/Set Button again to select the  
minutes digits, the MINUTES DIGITS will flash.  
4) Use the Up/Down Buttons to adjust the minutes to the  
appropriate time.  
5) You must press the Scan/Set Button again to complete the  
time setting.  
SETTING THE ALARM  
There are two different alarm modes on the Sonido Radio. You  
can choose to wake up to the radio or to a beep tone. You can  
set the alarm with the radio on or off.  
To set the type of alarm:  
1) To wake with the Radio, press and hold the Radio  
Alarm button (shown at right) for 2 seconds. The  
symbol will flash, you will hear a beep and the  
current alarm time will display.  
To wake with the Beep Tone Alarm, press and hold the  
Beep Tone Alarm button (shown at right) for 2 seconds.  
The  
symbol will flash, you will hear a beep and the  
current alarm time will display.  
Continued on page 9  
Page 8  
Sonido Radio  
 
Getting Started  
2) Immediately press and hold the Scan/Set button for  
3 seconds and you will hear a beep. The ALARM  
HOUR DIGIT and  
or  
will flash,  
SCAN  
depending on which type of alarm is being set.  
3) Using the Up/Down Tuning Buttons, select the  
appropriate hour digit and AM or PM.  
4) Press the Scan/Set Button again to select the minutes digits.  
The MINUTES DIGITS will flash.  
5) Use the Up/Down Tuning Buttons to adjust the minutes to the  
appropriate time.  
6) When finished press the Scan/Set Button. The  
symbol will be displayed.  
or  
Notes: If the Radio Alarm has been chosen, when the alarm time  
is reached the radio will play the last station selected at  
the same volume level last set.  
If there is no alarm symbol on the display, the alarm has  
not been activated.  
Dual alarm set:  
Follow steps 1-6 for both the Radio and Beep Tone  
Alarms. This allows you to set two different activation  
times and alarm types. This symbol (shown at right)  
will be displayed if both alarms are activated.  
Sonido Radio  
Page 9  
 
Getting Started  
BEEP TONE ALARM HWS(HUMANE WAKE SYSTEM)  
At the chosen alarm time a beep tone will sound and increase in  
volume every 15 seconds for one minute followed by one minute  
of silence before repeating the cycle. The HWS alarm will sound  
for one hour or until its turned off by pressing the power button.  
Once the power button has been pressed the alarm will reset  
itself to sound the next day at the time previously chosen.  
To shut off the alarm:  
Press and hold the Radio Alarm or Beep Tone Alarm  
Button until you hear a short beep and the alarm  
symbol disappears.  
SNOOZE FEATURE  
When the Radio or Beep Tone alarm is sounding, if you press any  
button except the Power Button, the alarm will temporarily stop for  
five minutes. The little Zsand Alarm symbol  
will  
flash on the display while the radio is in snooze mode.  
To shut off the alarm and snooze feature press the  
Power Button.  
DISPLAY BUTTON  
With the radio off, the display button activates the  
LCD backlight display. The light will remain on for  
approximately 15 seconds.  
With the radio on, the display button activates the LCD backlight  
display and switches the display from the frequency to the clock.  
To switch back to the frequency, press the display button again.  
Page 10  
Sonido Radio  
 
Getting Started  
SLEEP TIMER FEATURE  
Your Sonido Radio is equipped with a Sleep Timer that enables  
the radio to continue playing for up to 120 minutes after activa-  
tion, then shuts the radio off. Selectable times are 60, 45, 30, 15,  
120 and 90 minutes.  
Press and hold the Power/Sleep Button  
until the pictograph of a person in bed  
and the numbers 60 are displayed.  
Holding the Power / Sleep Button down will change the time in  
steps, showing times of 60, 45, 30, 15, 120 and 90 minutes. If  
you miss the time you want, simply continue holding the button  
until the desired time shows on the display. Release the button.  
Now the pictograph of the person in bed will appear on the dis-  
play. The radio will play for the allotted amount of time and then  
shut off. To deactivate the Sleep Timer, simply shut the radio off  
using the Power Button.  
Sonido Radio  
Page 11  
 
Radio Operation  
TUNING  
The Sonido Radio features four bands: AM / FM / TV Audio 2-13  
and Weather. Also the radio is equipped with three tuning  
methods: Manual tuning, Scan tuning, and Memory presets recall.  
Manual Tuning  
Refer to page 4 for Button Identification.  
1) Press the Power Button to turn on the radio.  
2) Select the band by pressing the Band Button.  
3) A single press of the Up or Down Tuning Buttons  
will change the frequency up or down for AM and  
SCAN  
FM bands, and channel up or down for Weather  
and TV bands.  
Each press of Up and Down Tuning Buttons will change the  
frequency by 10 kHz in AM mode and 200 kHz in FM mode.  
Tune to the next station by pressing and holding the tuning up or  
down for more than half a second.  
Scan Tuning  
SCAN  
Press the Scan button and the radio will search for  
stations and stop automatically when it finds an active  
one. After five seconds the radio will continue the scanning for  
another available station. To select a found station press the scan  
button once again.  
Scan Tuning will not work on the weather or TV bands. It may  
also stop scanning on strong interference or noise.  
Page 12  
Sonido Radio  
 
Radio Operation  
Memory Preset Tuning  
PRESETS  
5
1
2
3
4
Five stations may be stored into memory  
in each of the four bands.  
1) Tune to the station or channel you want to memorize.  
2) Press and Hold the desired Memory Preset Button for two  
seconds or until you hear a beep. The station or channel is  
then memorized.  
The display will show the memory number.  
To recall the memorized station, select the correct band and  
briefly press and release the Memory Button corresponding to sta-  
tion desired. The radio will instantly tune to the station stored in  
memory.  
Caution: If the preset button is held down for more than 2  
seconds when recalling a station, the station you are tuned  
to will now be stored in that memory position.  
WEATHER ALERT SYSTEM  
The WEATHER ALERT modes on the Sonido Radio can alert you  
to special weather related emergencies. During an emergency or  
weather-related hazard, NOAA issues an emergency tone that will  
set off an audible and/or visual alarm on the radio.  
NOTE: Hazard warnings are not available in all areas.  
There are seven standard NOAA weather channels used in the  
US and Canada. This radio receives broadcasts up to 40 miles  
from transmitting stations.  
Sonido Radio  
Page 13  
 
Radio Operation  
1) To listen to the standard NOAA weather channels, turn the  
radio on, press the Band button until WX shows on the dis-  
play. The telescopic whip antenna may need to be fully  
extended and in the upposition to receive a station clearly.  
2) The channel number of the weather station is shown on the  
display. Pressing the Up or Down Tuning Buttons will toggle  
you through the seven-programmed channels. There should  
be one or more weather service stations broadcasting in your  
local area. You will hear a report that is updated usually once  
or more per day for your area. If there is a severe weather or  
weather-related emergency, NOAA may update the weather  
broadcast more frequently. If there is a weather emergency,  
the NOAA may issue an alert tone.  
After locating and tuning in your weather station the radio can  
now be placed into WEATHER ALERT mode. The WEATHER  
ALERT mode enables you to listen to your favorite AM or FM  
station or turn the radio off, and still receive an alert signal  
warning you of a special emergency. There are three active  
WEATHER ALERT modes on the Sonido Radio.  
Setting the Weather Alert  
1) To place the radio in WEATHER ALERT mode,  
press and hold the Weather Alert Button for two  
seconds: You will hear a short beep and see  
the ALERT symbol, shown on the display.  
This WEATHER ALERT mode is with the flashing  
light only (no Alarm). If NOAA issues a weather  
related emergency, the radio will automatically alert  
ALERT  
you with a small flashing light above the Weather Alert Button.  
The Alert light continues to flash until any button is pushed.  
Continued on page 15  
Page 14  
Sonido Radio  
 
Radio Operation  
2) To access the second mode (WEATHER ALERT with flashing  
light and siren). Press and hold the WEATHER ALERT Button  
again for two seconds until you hear a long beep. The sym-  
bol shown at right will appear and the red light  
ALERT  
above the WEATHER ALERT Button comes on  
continuously. In this mode, if a NOAA alert tone  
is issued, the red light above the WEATHER  
ALERT Button flashes and a siren turns on for up to 1 minute.  
In this mode, when the siren is active, pressing any button on  
the radio instantly turns the radio to the Weather Audio and  
cancels the siren.  
3) To access the third mode, (WEATHER ALERT with NOAA  
Audio) press and hold the WEATHER ALERT  
Button again for two seconds until you hear a  
ALERT  
quick double beep. The symbol shown at right  
will be displayed in this mode. In this mode, if a  
NOAA alert tone is issued, the red light flashes and the radio  
switches to Weather Audio automatically. To cancel the  
WEATHER ALERT, press the Band Button on the radio.  
Turning Off the Weather Alert  
Press the WEATHER ALERT Button again for two seconds. A  
high/low beep will sound: You will no longer see the word ALERT  
in the display of the radio, which indicates that the alarm has  
been deactivated.  
Note: If the word ALERT still appears then the weather alert has  
not been deactivated but changed to the next weather  
alert setting. Press the WEATHER ALERT Button again for  
two seconds to cycle through until the word ALERT no  
longer displays.  
Sonido Radio  
Page 15  
 
Radio Operation  
Notes on the Weather Alert  
1) If you have the headphones plugged in and a weather alert is  
issued, the audio to the headphones will be cut-off and the  
siren will sound through the radio's speaker.  
2) In any of the active WEATHER ALERT modes, the weather  
receiver stays on and listens for an emergency tone issued  
from NOAA in case of emergency.  
3) You may get a periodic test tone from the NOAA that will  
cause an unexpected alarm on your Sonido Radio. This  
tone is only a test and will happen periodically, usually  
every Wednesday at noon, or whenever the agency decides to  
test their emergency alert system. Simply pressing any button  
on the receiver will shut the alert tone off. After an alert has  
been issued, the WEATHER ALERT siren will stay on for one  
minute and the light will flash for one hour or until you turn it  
off by pressing any button.  
4) When activated, the WEATHER ALERT consumes power  
even when the radio is turned off.  
5) Be aware that if you are not using AC power the WEATHER  
ALERT will completely drain your batteries. If your batteries  
are dead and AC power is off, the Weather Alert Alarm will  
not work.  
SETTING TUNING STEPS  
Tuning steps in some countries are different from others. If you  
purchased this radio in the United States (which uses 10kHz-tun-  
ing steps) and intend to use it in Europe (which has 9kHz-tuning  
steps) you will need to adjust the radio so that it can match the  
locations tuning steps.  
1) When the radio is switched off, press and hold the  
Step/Band button for three seconds. This will show  
the current FM tuning step. Continue pressing the  
Step/Band button for five more seconds. A beep will  
sound and the display will show FM and flash the current  
tuning steps.  
Continued on page 17  
Page 16  
Sonido Radio  
 
Radio Operation  
2) By pressing Tuning Down, you may adjust the steps from  
200kHz for U.S. or 100kHz per step for Europe.  
3) After the FM step is selected, press the Step/Band button  
again to bring up the AM step selections. The display  
will show AM and flash 10 kHz tuning steps. By pressing  
Tuning Down, you may adjust the steps from 10kHz to 9kHz  
per step for Europe.  
4) Complete the setting by pressing the Step/Band button once  
again.  
AUX IN Jack  
The green jack, labeled AUX IN, is used to connect an external  
audio source such as an MP3 Player, CD, or recorder, so you  
can listen through your Sonido Radios speaker. To  
do this, you will need the appropriate  
AUX In  
Jack  
patch cord. Refer to page 18 for  
specifications. With a patch cord  
connected, press the Step/Band  
button until AU appears on the dis-  
play.  
Headphone  
Jack  
Warning: If a "LINE OUT" is not available on your  
external audio source, you can use the headphone  
jack. However, the volume must be kept low or audio  
distortion may result.  
HEADPHONE JACK  
You can use a stereo or mono headphone (located on the left  
hand side of your radio) with a 3.5mm plug. When you insert  
headphones into the headphone jack, the speaker is disconnect-  
ed and this radio provides FM stereo through the headphones.  
Note: If using a mono headphone jack or a single earphone  
piece, the FM sound will be in mono. A limited number of  
earpieces may not work properly. Call for advice.  
Sonido Radio  
Page 17  
 
Specifications  
FREQUENCY COVERAGE  
FM Band:  
AM Band:  
TV Band:  
87.5 - 108 MHz Stereo  
520 - 1710 kHz  
Channels 2-13 Audio Only  
WEATHER BAND  
Channel 1:  
Channel 2:  
Channel 3:  
Channel 4:  
162.400 MHz Channel 5:  
162.500 MHz  
162.525 MHz  
162.550 MHz  
162.425 MHz Channel 6:  
162.450 MHz Channel 7:  
162.475 MHz  
POWER SOURCE  
AC 120 Volts 60Hz  
Batteries: (4) "D" size  
AUDIO  
Speaker: 3", 4 Ohm, 2 Watts  
ANTENNA  
FM, TV and Weather Band: Telescopic whip antenna  
AM Band: Built-in Ferrite Bar - 7/16" dia x 6.25" long (12mm x 160 mm)  
DIMENSIONS  
9" W x 5.25" H x 2.25" D (at the base)  
WEIGHT  
Approximately 1.7 pounds without batteries  
Note: Specifications are subject to change without notice.  
6V DC JACK  
Center tipped negative. 6V DC @ 400mA input. Center point negative.  
Page 18  
Sonido Radio  
 
Troubleshooting Guide  
My radio shuts off after just a few seconds:  
Low batteries can cause this situation. Replace them with a new  
set of batteries. If the radio is operating on the power adapter,  
check for solid connections at the wall outlet and the side of the  
radio. Also make sure there is power at the wall outlet.  
Stations won't hold in memory:  
The memory button settings are being overwritten. When recalling  
a station from memory, if you hold the memory button down too  
long it will program the current station over your previously stored  
station. To recall a station that has been stored in memory, always  
press and release the button quickly. To program a new station  
into memory, tune to the desired station and then press and hold  
the memory button for two seconds until you hear a beep. Also,  
please see the section on Memory Tuning on page 13.  
The AM reception is poor inside of my building:  
Many building materials have adverse effects on AM band listen-  
ing. Brick, concrete, stucco, and aluminum siding all have a ten-  
dency to absorb or reflect the AM signal. Spanish tiles or metal  
roofs are also culprits. To test your AM reception, put batteries in  
your radio and take it outside of the building. If your reception is  
notably stronger outside than inside the building, an external AM  
antenna may be necessary to bring the signal into the building.  
Poor reception on FM, TV Audio, or Weather bands:  
The Sonido Radio uses its telescopic, or whipantenna for FM,  
TV audio, and the weather bands. To improve reception of these  
bands, fully extend the telescopic antenna. Reception of FM and  
weather broadcasts is normally improved with the antenna  
extended straight up. TV audio reception usually requires the  
antenna to be rotated at an angle. Note: The antenna must be  
fully extended to allow it to rotate.  
Sonido Radio  
Page 19  
 
Radio Noise Troubleshooting  
AM RADIO NOISE PROBLEMS AND POSSIBLE SOLUTIONS  
If you hear an annoying buzz when listening to AM radio, it's  
most likely radio noise. Here are some of the usual culprits:  
*
*
Dimmer switch (even in an adjacent room).  
Lights: fluorescent light, touch lamptype fixtures, auto-  
matic night lights, motion-activated outdoor lights, dying  
bulbs, blinking bulbs.  
*
*
*
*
*
*
*
Nearby television or computer.  
Electronic bug and pest controllers.  
Faulty electrical switch.  
Radios scanners.  
Dirty insulators on a nearby power pole.  
Electric blanket.  
Smoke detectors that run from an AC current (battery  
operated units are OK).  
Now what can you do about it?  
*
Turn off the circuit breakers to see if the noise stops, and if  
the source comes from inside your house. Turn off one circuit  
at a time to isolate the source of the noise.  
*
Using a battery-operated radio, check if the interference  
comes from the AC 120V line, through the air, or both. To  
locate the direction of the noise, turn the radio until you hear  
the loudest noise. The front and the back of the radio will  
point to the noise origin.  
*
*
If the noise comes from outside, carry the radio around the  
neighborhood to check for the origin of the noise. Ask your  
neighbors if they hear the same noise.  
If you suspect a power pole, call the utility company. Dirty  
power pole insulators are sometimes a cause of hard-to-find  
radio interference.  
For more information on Radio Noise Troubleshooting, go to  
Page 20  
Sonido Radio  
 
AM Tuning & Listening Tips  
Most portable radios including the Sonido Radio have an internal  
AM antenna. Best performance is achieved when the radio is  
swiveled on its base for maximum signal pickup from the transmit-  
ting tower. This same technique can be used to help nullify  
unwanted signals or radio noise. Experimentation is the best way  
to see how it works for you.  
Daytime reception is limited to about 300 miles maximum  
because you can only receive the signal directly from the trans-  
mitter site. You may receive AM stations thousands of miles away  
at dawn, dusk and at night, depending on the time of year and  
atmospheric conditions. The ionosphere is a layer of ions above  
the earth. At night it slows and congeals into a giant mirror and  
can reflect radio waves back to the earth, allowing you to receive  
signals much farther away than during the day.  
Distant listening is called DXing. One club that is devoted to  
DXing is National Radio Club at: PO Box 164, Mannsville, NY  
Sonido Radio  
Page 21  
 
Safety Instructions  
READ BEFORE OPERATING EQUIPMENT  
SAVE THESE INSTRUCTIONS  
1) Read and understand all safety and operating instructions  
before the radio is operated.  
2) Retain Instructions: The safety and operating instructions should  
be retained for future reference.  
3) Heed Warnings: All warnings on the appliance and in the operat-  
ing instructions should be followed.  
4) Water and Moisture: The appliance should not be used near  
water. Do not use near a bathtub, washbowl, laundry tub,  
kitchen sink, wet basement, swimming pool, etc.  
5) Cleaning: Unplug the receiver from the AC power outlet before  
cleaning. Use only a damp cloth for cleaning the exterior of the  
receiver.  
6) Placement: Do not place the radio on an unstable cart, stand,  
bracket or table. The radio may fall, causing serious personal  
injury and damage to the receiver.  
7) Heat: Never put the radio in direct sunlight in an unventilated  
area or behind glass like a car's interior. The appliance should  
be away from heat sources such as radiators, heat registers,  
stoves, or other appliances that produce heat.  
9) Power Adapter Cord: The power adapter cord should be positioned  
so it is not walked on or pinched, or have items placed on top of it.  
Pay particular attention to cords at plugs, convenience receptacles,  
and the point where they exit from the unit. Unplug the power  
adapter by gripping the power transformer, not the cord. Operate the  
radio using only the correct type of power source indicated. If you  
are not sure of the type of power supply to your home, consult your  
dealer or local power company.  
10) Do not overload wall outlets or extension cords. This can result in a  
risk of fire or electrical shock. Never insert objects of any kind into  
the receiver through openings. The objects may touch dangerous  
voltage points or short out parts. This could cause a fire or electrical  
shock.  
Page 22  
Sonido Radio  
 
Safety Instructions  
11) If the radio is left unattended and unused for long periods of time,  
unplug it from the wall outlet. This will prevent damage caused by  
lightning or power line surges.  
12) If the radio is left unattended and unused for long periods of time,  
remove the batteries. The batteries may leak and damage furniture  
or your radio.  
13) Do not attempt to service the receiver yourself. Removing the cover  
may expose you to dangerous voltage, and will void the warranty.  
Refer all servicing to authorized service personnel.  
15) The appliance should be serviced by qualified service personnel  
when:  
A. The power adapter or the transformer has been damaged, or  
B. Objects have fallen or liquid has been spilled into the radio, or  
C. The radio has been exposed to rain, or  
D. The radio does not appear to operate normally or exhibits a  
marked change in performance, or  
E. The radio has been dropped or the enclosure damaged.  
16) The user should not attempt to service the appliance beyond that  
described in the operating instructions. All other servicing should be  
referred to qualified service personnel. This symbol is to alert  
you to important operation or servicing instructions that may  
appear in the owners manual.  
Model: PR-D4VW  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.  
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.  
1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  
2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,  
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED  
OPERATION.  
Notice: Any changes or modifications not expressly approved by the  
party responsible for compliance could void the user's authority to oper-  
ate the equipment.  
Sonido Radio  
Page 23  
 
381C15SA  
 

BIXOLON Automobile Accessories TTGO129 ST RVC User Manual
Black Box Log Splitter AC156A 8 User Manual
Blaupunkt Car Stereo System AUGSBURG C30 User Manual
Bosch Appliances Boiler 100 Combi Boiler User Manual
Bosch Appliances Clothes Dryer WTMC5321US CN User Manual
Braun Thermometer IRT 1020 User Manual
Brother Sewing Machine Brother CP 6500 User Manual
Canon Calculator LS 154TG User Manual
Canon Calculator LS 270G User Manual
Century Stroller 6965 User Manual